manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

Z07254

M3 M4

M1 M2

Z07255

Wire Harness Side

SA

−

102

−

SUSPENSION AND AXLE

DIFFERENTIAL LOCKING SYSTEM

959

Author:

Date:

1996 LAND CRUISER   (RM451U)

(6)

Check the voltage between the terminals of the Diff.
lock ECU when switching the Diff. lock control
switch with the speedometer, registering approx. 8
km/h (5 mph) or more.

(7)

Check that the indicator lights blink when center
Diff. lock release mode is set.
Diff. lock is released for both the front wheels and
rear wheels at this time.

(8)

Return the Diff. lock control switch to OFF.

(9)

Stop the engine and lower the vehicle.

2.

INSPECT DIFF. LOCK SYSTEM CIRCUIT

(a)

Inspect the system circuit with connector disconnected.
Disconnect the connector from the Diff. lock ECU and in-
spect the connector on the wire harness side, as shown
in the chart.

Trouble Part/

Terminals (Symbols)

Condition

Specified Value

Rear diff. lock actuator/

1 (M2) 

−

 3 (M1)

−

Less than 100 

Ω

Front diff. lock actuator/

5 (M4) 

−

 7 (M1)

−

Less than 100 

Ω

Body ground/

13 (GND) 

−

 Body ground

−

Continuity

Vehicle speed sensor/

4(SPD) 

−

 Body ground

Vehicle moving slowly

1 pulse each 40 cm (15.75 in.)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Samsung HF1000 User Manual preview
HF1000
Бренд: Samsung Страницы: 133
JANE MICRO Quick Start Manual preview
MICRO
Бренд: JANE Страницы: 6
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Бренд: iDataLink Страницы: 99
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Бренд: Cadillac Страницы: 522
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
Thule Kit 1429 Fitting Instructions Manual preview
Kit 1429
Бренд: Thule Страницы: 8
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Бренд: TATA Motors Страницы: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Бренд: Safe Fleet Страницы: 12
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Бренд: Vauxhall Страницы: 131
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
Veldo Teknoloji DUCATO Manual preview
DUCATO
Бренд: Veldo Teknoloji Страницы: 32
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Бренд: INDIWORK Страницы: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Бренд: Opel Страницы: 103
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Бренд: RAM Страницы: 360
Gacell SLH 27C User Manual preview
SLH 27C
Бренд: Gacell Страницы: 25
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Бренд: AUTOTECH Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды