manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

Input Signal

Indicator Light

Blinking Pattern

Stop Light 

switch ON

Light

ON

OFF

SW OFF

SW ON

DI

−

314

−

DIAGNOSTICS

CRUISE CONTROL SYSTEM

1996 LAND CRUISER   (RM451U)

Stop Light Switch Circuit

CIRCUIT DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECU. When the ECU receives
this signal, it cancels the cruise control.
A fail

−

safe function is provided so that the cancel functions normally, even if there is a malfunction in the stop

light signal circuit.
The cancel conditions are: Battery positive voltage at terminal STP

−

When the brake is on, battery positive voltage normally applies through the STOP fuse and stop light switch
to terminal STP

−

 of the ECU, and the ECU turns the cruise control off.

If the harness connected to terminal STP

−

 has an open circuit, terminal STP

−

 will have battery positive volt-

age and the cruise control will be turned off.
Also, when the brake is on, the magnetic clutch circuit  is cut mechanically by the stop light switch, turning
the cruise control off (See page 

DI

−

298

 for operation of the magnetic clutch).

WIRING DIAGRAM

See page 

DI

−

298

.

INSPECTION PROCEDURE

1

Check operation of stop light.

CHECK:

Check that stop light comes on when brake pedal is depressed, and turns off when brake pedal is released.

NG

Check stop light system (See page 

BE

−

24

).

OK

2

Input signal check.

CHECK:

(a)

See input signal check on 

DI

−

286

.

(b)

Check the indicator light when the brake pedal is de-
pressed.

OK:

The indicator light goes off when the brake pedal is
depressed.

OK

Proceed to next circuit inspection shown on

problem symptoms table (See page 

DI

−

295

).

NG

DI5OI

−

02

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Бренд: GMC Страницы: 140
Jeep Compass Overview Manual preview
Compass
Бренд: Jeep Страницы: 25
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
Pacbrake C44059 Installation Manual preview
C44059
Бренд: Pacbrake Страницы: 14
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Бренд: Curt Manufacturing Страницы: 6
Fiat 500 L 2019 User Manual preview
500 L 2019
Бренд: Fiat Страницы: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Бренд: Honda Страницы: 6
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Бренд: Waeco Страницы: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Бренд: Tusk Страницы: 2
U.S. General 95904 Operating Instructions preview
95904
Бренд: U.S. General Страницы: 4
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Бренд: RBP Страницы: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Бренд: HURST Страницы: 2
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Бренд: Safe Fleet Страницы: 12
aci ADARAC Aluminum M Series Installation Instructions Manual preview
ADARAC Aluminum M Series
Бренд: aci Страницы: 16
Imiola HAK-POL O/018 Quick Manual preview
O/018
Бренд: Imiola HAK-POL Страницы: 3
Kargo Master 8006A Instruction Manual preview
8006A
Бренд: Kargo Master Страницы: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Бренд: Safe Fleet Страницы: 12
Pacbrake HP10098 Installation Manual preview
HP10098
Бренд: Pacbrake Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды