Thermo Scientific thermoscientific Vanquish Pumps C Скачать руководство пользователя страница 273

Страница: 273 / 296

•

Accessories, Consumables and Replacement Parts

Pumps C, Pumps F ( VC-Pxx, VF-Pxx)
Operating Manual

Page 273

12.4 Consumables and Replacement Parts

The following consumables and replacement parts are available for the
pump.

12.4.1 Maintenance Kits

The maintenance kits that are available for the pumps include all parts
that are required for routine maintenance.

•

See

Maintenance Kits (VC-Pumps) (

}

page 273)

•

See

Maintenance Kits (VF-Pumps) (

}

page 275)

12.4.1.1

Maintenance Kits (VC-Pumps)

TIP

Maintenance kits can include parts that are not required for your

specific pump. These parts are marked accordingly in the contents lists
for the kits.

VC-P10

Description

Part No.

Maintenance kit for VC-P10, including:

•

Pump head seal (2 PTFE seals (2 each), different sized)

•

Silicone tubing (clear tubing)

•

Peristaltic tubing (white tubing)

•

Tubing connector (straight) (pack of 5)

•

Tubing connector (90°-angled)

•

Seal wash seal (pack of 4)

•

Piston seal (pack of 4)

•

Valve cartridge, ceramics (pack of 2)

•

Solvent line filter (4 filter holders and filter frits)

•

Cleaning swab (pack of 5)

•

Tubing clip (self-adhesive) (pack of 3)

Not required with VC-P10:

•

Cap seal for purge valve knob without integrated seals

•

Support ring

6040.1953A

Содержание thermoscientific Vanquish Pumps C









































































































































































































































































































Результаты поиска

Содержание thermoscientific Vanquish Pumps C

Отзывы:

Похожие инструкции для thermoscientific Vanquish Pumps C

Бренды по названию

Популярные бренды

Thermo Scientific thermoscientific Vanquish Pumps C, Руководство по эксплуатации

Результаты поиска

Содержание thermoscientific Vanquish Pumps C

Отзывы:

Похожие инструкции для thermoscientific Vanquish Pumps C

Бренды по названию

Популярные бренды