manualshive.com logo in svg

Thermo Scientific thermoscientific Vanquish Pumps C, Руководство по эксплуатации


Поделиться
Скачать
background image

2

 • 

Safety

Pumps C, Pumps F ( VC-Pxx, VF-Pxx) 
Operating Manual

Page 21

2.3

Safety Precautions

2.3.1

General Safety Information

All users must observe the general safety information presented in this
section and all specific safety messages and precautionary statements
elsewhere in this manual during all phases of installation, operation,
troubleshooting, maintenance, shutdown, and transport of the device.

If the device is used in a manner not specified by Thermo Fisher
Scientific, the protection provided by the device could be impaired.
Observe the following:

•

Operate the device only within its technical specifications.

•

Use only the replacement parts and additional components, options,
and peripherals specifically authorized and qualified for the device
by Thermo Fisher Scientific.

•

Perform only the procedures that are described in this operating
manual and in supporting documents for the device. Follow all
instructions step by step and use the tools recommended for the
procedure.

•

Open the enclosure of the device and other components only if
specifically instructed to do so in this manual.

•

Thermo Fisher Scientific cannot be held liable for any damage,
material or otherwise, resulting from inappropriate or improper use
of the device. If there is any question regarding appropriate usage,
contact Thermo Fisher Scientific before proceeding.

Safety Standard

This device is a Safety Class I instrument (provided with terminal for
protective grounding). The device has been manufactured and tested
according to international safety standards.

Содержание thermoscientific Vanquish Pumps C









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для thermoscientific Vanquish Pumps C

GE Responder 2000 Service Manual preview
Responder 2000
Бренд: GE Страницы: 138
EASTERN INSTRUMENTS CentriFlow Manual preview
CentriFlow
Бренд: EASTERN INSTRUMENTS Страницы: 93
EarthQuake 9800B Operating & Parts Manual preview
9800B
Бренд: EarthQuake Страницы: 12
Pari Vortex Instructions For Use preview
Vortex
Бренд: Pari Страницы: 2
Eaton SPD Series Instruction Booklet preview
SPD Series
Бренд: Eaton Страницы: 16
Eaton 2596 Installation, Operation & Maintenance Manual preview
2596
Бренд: Eaton Страницы: 15
Garmin GNX Wind Owner'S Manual preview
GNX Wind
Бренд: Garmin Страницы: 10
Naviom AIS Installation Instructions Manual preview
AIS
Бренд: Naviom Страницы: 31
iHealth PO3M Quick Start Manual preview
PO3M
Бренд: iHealth Страницы: 8
laerdal MegaCode Kelly Manual preview
MegaCode Kelly
Бренд: laerdal Страницы: 8
LAHTI PRO 46018 User Manual preview
46018
Бренд: LAHTI PRO Страницы: 16
laerdal LSU Directions For Use Manual preview
LSU
Бренд: laerdal Страницы: 32
laerdal Resusci Anne Important Product Information preview
Resusci Anne
Бренд: laerdal Страницы: 32
laerdal ALS Simulator Manual preview
ALS Simulator
Бренд: laerdal Страницы: 8
Raytec VARIO2 series Full Installation And Setup Manual preview
VARIO2 series
Бренд: Raytec Страницы: 60
Yamaha MCX-C15 - MusicCAST Network Audio Player Owner'S Manual preview
MCX-C15 - MusicCAST Network Audio Player
Бренд: Yamaha Страницы: 65
Yamaha Audiogram6 Manuel Du Propriétaire preview
Audiogram6
Бренд: Yamaha Страницы: 24
Easylife KMS005M Instruction Manual preview
KMS005M
Бренд: Easylife Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды