manualshive.com logo in svg

Thermo Scientific thermoscientific Vanquish Pumps C, Руководство по эксплуатации


Поделиться
Скачать
background image

2

 • 

Safety

Page 26

Pumps C, Pumps F ( VC-Pxx, VF-Pxx) 

Operating Manual

2.4

Solvent and Additive Information

2.4.1

General Compatibility

To protect optimal functionality of the Vanquish system, observe these
recommendations on the use of solvents and additives:

•

The system must be used with reversed-phase (RP) compatible
solvents and additives only.

•

Use only solvents and additives that are compatible with all parts in
the flow path.

TIP

 In a Vanquish Core system, normal-phase (NP) compatible solvents

and additives may be used if the VC-pumps and the VC-autosamplers are
modified with the components from the Normal-Phase (NP) kit. See

Normal-Phase Compatible Solvents and Additives (

}

 page 249)

.

NOTICE

If the system flow path includes a Vanquish charged aerosol detector,
observe the specific solvent and additive information for this detector.
Refer to the 

Operating Manual 

for the Vanquish charged aerosol

detector.

Содержание thermoscientific Vanquish Pumps C









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для thermoscientific Vanquish Pumps C

Gardena 1407 Operator'S Manual preview
1407
Бренд: Gardena Страницы: 13
XAG P30 Quick Start Manual preview
P30
Бренд: XAG Страницы: 24
Abicor Binzel FES-200 W3 Short Instruction preview
FES-200 W3
Бренд: Abicor Binzel Страницы: 92
Hanna Instruments HI 98311 Instruction Manual preview
HI 98311
Бренд: Hanna Instruments Страницы: 2
Hanna Instruments HI981520 Quick Reference Manual preview
HI981520
Бренд: Hanna Instruments Страницы: 2
Hanna HALO 2 Instruction Manual preview
HALO 2
Бренд: Hanna Страницы: 12
Hanil T04 User Manual preview
T04
Бренд: Hanil Страницы: 24
Hanil Supra R17 User Manual preview
Supra R17
Бренд: Hanil Страницы: 32
Hanil Component R12 Operation Manual preview
Component R12
Бренд: Hanil Страницы: 24
Safety 1st HS129 Manual preview
HS129
Бренд: Safety 1st Страницы: 4
Safety Engineering SELF BELAY Installation Manual preview
SELF BELAY
Бренд: Safety Engineering Страницы: 5
ICON Health & Fitness WEIDER SHAPE GLIDER WECR43062 User Manual preview
WEIDER SHAPE GLIDER WECR43062
Бренд: ICON Health & Fitness Страницы: 6
Duracell 689314 Assembly And Installation Instructions preview
689314
Бренд: Duracell Страницы: 2
XPOtool 62547 Operation Manual preview
62547
Бренд: XPOtool Страницы: 10
MAHLE ArcticPro 200yf Quick Manual preview
ArcticPro 200yf
Бренд: MAHLE Страницы: 2
SAM MEDICAL Junctional Tourniquet Quick Start Manual preview
Junctional Tourniquet
Бренд: SAM MEDICAL Страницы: 2
Wealden Rehab N3242-1 Heron Lift E Operation & Maintenance Manual preview
N3242-1 Heron Lift E
Бренд: Wealden Rehab Страницы: 11
Lanta LED Gyro Ball Owner'S Handbook Manual preview
LED Gyro Ball
Бренд: Lanta Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды