manualshive.com logo in svg

Thermo Scientific thermoscientific Vanquish Pumps C, Руководство по эксплуатации


Поделиться
Скачать
background image

8

 • 

Troubleshooting

Page 198

Pumps C, Pumps F ( VC-Pxx, VF-Pxx) 

Operating Manual

8.1

General Information about Troubleshooting

The following features help you to identify and eliminate the source for
problems that may arise during operation of the device.

NOTICE

When the Vanquish system includes a Vanquish charged aerosol
detector, the detector may affect the operation and/or performance of
the pump. For example, errors in the detector may affect the pump by
automatically stopping the pump flow. For more information, refer to
the 

Operating Manual

 for the detector.

TIP

 For information about operating issues that might occur during the

operation of a Vanquish system, refer to the 

Vanquish System Operating

Manual

.

If you are unable to resolve a problem following the instructions given
here or if you experience problems that are not covered in this section,
contact Thermo Fisher Scientific Technical Support for assistance. See
the contact information at the beginning of this manual.

To facilitate device identification, have the serial number and technical
name available when communicating with Thermo Fisher Scientific.

Status Indicators

The status indicator LED bar on the front side of the device and the

STATUS

 LED on the keypad inside provide quick visual feedback on the

operational status of the device. If the device firmware detects a
problem, the status indicators are red. The problem is reported to the
Chromeleon software and a message appears in the Audit Trail.

Pump Block Status LED

The status indicator LED is located inside the pump above the pump
head (pump block LED). The LED indicates the operational status of the
pump block.

Alarms

Leaks are a potential safety issue. Therefore, if a leak sensor detects
leakage, beeping starts to alert you in addition to the message in the
Chromeleon Audit Trail and the status indicators changing to red. Follow
the instructions in this manual to find and eliminate the source for the
leakage.

Содержание thermoscientific Vanquish Pumps C









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для thermoscientific Vanquish Pumps C

Major 4200 Operator'S Manual & Parts List preview
4200
Бренд: Major Страницы: 52
Hach MET ONE 3400 Series User Manual preview
MET ONE 3400 Series
Бренд: Hach Страницы: 48
Panta Safe Light Solar Quick Start Manual preview
Solar
Бренд: Panta Safe Light Страницы: 2
Calrec OMEGA Installation Manual preview
OMEGA
Бренд: Calrec Страницы: 70
RAPID REBOOT GENESIS Start Manual preview
GENESIS
Бренд: RAPID REBOOT Страницы: 18
MacDon M1240 Unloading And Assembly Instructions preview
M1240
Бренд: MacDon Страницы: 170
MacDon D1X Series Assembly Instructions Manual preview
D1X Series
Бренд: MacDon Страницы: 108
MacDon D1X Series Unloading And Assembly Instructions preview
D1X Series
Бренд: MacDon Страницы: 108
MacDon R80 Unloading And Assembly Instructions preview
R80
Бренд: MacDon Страницы: 51
MacDon R80 Operator'S Manual preview
R80
Бренд: MacDon Страницы: 104
MacDon A40-D Operator'S Manual preview
A40-D
Бренд: MacDon Страницы: 240
Macherey-Nagel QUANTOFIX Relax Manual preview
QUANTOFIX Relax
Бренд: Macherey-Nagel Страницы: 192
MacDon A30-D Operator'S Manual preview
A30-D
Бренд: MacDon Страницы: 182
MacDon A30-S Operator'S Manual preview
A30-S
Бренд: MacDon Страницы: 192
MacDon M105 Unloading And Assembly Instructions preview
M105
Бренд: MacDon Страницы: 53
MacDon M155E4 Operator'S Manual preview
M155E4
Бренд: MacDon Страницы: 2
KCI ActiV.A.C. Quick Reference Manual preview
ActiV.A.C.
Бренд: KCI Страницы: 2
KCI ActiV.A.C. International User Manual preview
ActiV.A.C.
Бренд: KCI Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды