Siklu EtherHaul 1200 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 234

background image

Installation and User Manual

EtherHaul

1200™

EH-INST-02, Issue 4.0

Page 55

| auto-neg | loopback-mode | loopback-timeout | statistics

| alarm-propagation}]]

The following is an example of an Ethernet interface status display.

Local_Site> show eth eth1

eth eth1 description : Siklu

eth eth1 mtu : 9216

eth eth1 mac-addr : 00:24:a4:00:06:d2

eth eth1 admin : up

eth eth1 operational : up

eth eth1 last-change : 0000:00:12:11

eth eth1 name : Eth1

eth eth1 alias :

eth eth1 eth-type : 1000fd

eth eth1 eth-act-type : 1000fd

eth eth1 auto-neg : enabled

eth eth1 loopback-mode : disabled

eth eth1 loopback-timeout : 60

eth eth1 alarm-propagation : disabled

Table

‎

11-18

on page 211 lists and describes the configurable Ethernet interface

attributes.

Table

‎

11-19

on page 214 lists and describes the read-only Ethernet interface

attributes.

4.7

Default VLAN Setting

EtherHaul’s Undefined VLAN feature enables transparent forwarding of both tagged and
untagged traffic by default. No configuration or license is necessary for this feature,
which gives you the flexibility to change your VLANs with no additional configuration
necessary in the EtherHaul system.

For VLAN configuration options, including the ability to define or block specific VLANs,
refer to

Configuring VLANs

on page 64.

«
...
53
54
55
56
57
...
»

Содержание EtherHaul 1200











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EtherHaul 1200

Бренд: Parsec Technologies Страницы: 21

Бренд: L3 Страницы: 122

Бренд: Schwarzbeck Страницы: 6

Бренд: Vivanco Страницы: 12

Бренд: Insignia Страницы: 2

AirLancer ON-Q360ag

Бренд: Lancom Страницы: 5

Бренд: Zehnder Rittling Страницы: 9

104590-1 FPD.5-5.8-18

Бренд: Radio Waves Страницы: 5

Бренд: CommScope Страницы: 4

Бренд: WADE Antenna, Inc. Страницы: 4

DAT 790 HD BOSS LR

Бренд: Televes Страницы: 4

OYSTER V PREMIUM

Бренд: Ten-Haaft Страницы: 52

Бренд: Aukey Страницы: 21

Бренд: Solid Signal Страницы: 2

Бренд: Clas Ohlson Страницы: 5

Бренд: Winegard Страницы: 1

Бренд: Valcom Страницы: 18

Бренд: Icom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды