Siklu EtherHaul 1200 Скачать руководство пользователя страница 43

Страница: 43 / 234

Installation and User Manual

EtherHaul

1200™

EH-INST-02, Issue 4.0

Page 43

Manually setting the Role is necessary only for asymmetric configurations.



Transmit Asymmetry

– Default value is symmetric configuration: 50% for Tx

and Rx (

50tx-50rx

). For an asymmetric configuration (75%/25% or 90%/10%),

you will have to manually configure the Role and set the Master unit to

75tx-

25rx (or 90tx-10rx)

and

the Slave unit to

25tx-75rx (or 10tx-90rx)

. Default

value is

50tx-50rx



Mode

– Select one of the following operation modes:

Alignment

– Carrier Wave transmission. Used for antenna

alignment.

Adaptive

– Adaptive Bandwidth, Code, and Modulation.

Static

– Fixed modulation profile. If you select

Static

, you must

select from a list of pre-configured modulation profiles in the

Modulation

field.

Default value is

Adaptive



Modulation

– qpsk, 16QAM, or 64QAM.



Sub Channels

– From 1 to 4 (occupied bandwidth. For Channel Width

250MHz: 62.5-250MHz, For Channel Width 500MHz: 125-500MHz)



Repetitions

– 1,2 or 4



FEC Rate

– 0.5

When using the system in Static mode, you must select from a pre-defined list of
modulation profiles. In Adaptive mode, the ODU will switch among the
modulation profiles from this list.

To check the available modulation profiles, refer to

Viewing Modulation Profiles

Using the Web EMS

on page



Tx and Rx Link ID

–You can set unique Link IDs for links installed on the same

site to avoid locking on the wrong transmitter.



Operational Status

– Displays the radio link status (Up or Down).



Tx and Rx State

–Displays the Tx and Rx chains status.



RSSI (dBm)

– Displays the Receiver Signal Strength Indicator.



CINR (dB)

– Displays the Carrier to Interf Noise ratio, which

indicates the radio link’s signal quality. In normal conditions, CINR≥17
indicates a good signal quality.



Tx Power (dBm)

–ODU’s transmit power (+5 to -35dBm).

Adjust Tx Power so the RSSI at the remote end will not be higher than -35dBm

(overload threshold).



Tx Mute

– set to

Enable

to mute the transmitter



Tx mute Timeout (seconds)

– number of seconds for Tx mute enabled

Содержание EtherHaul 1200











































































































































































































































Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды

Siklu EtherHaul 1200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды