Siklu EtherHaul 1200 Скачать руководство пользователя страница 220

Страница: 220 / 234

Installation and User Manual

EtherHaul

1200™

Page 220

EH-INST-02, Issue 4.0

Attribute (CLI

Attribute Name)

Description

SNMP Object ID

Value

Access

Default

Bridge Port

Acceptable Frame

Types (admit)

The frame types that will be

accepted on the port and

assigned to a VID.
VID assignment is based on

the PVID and VID Set for the

port.
When this is admitTagged(3),

the device will discard

untagged frames or Priority-

Tagged frames received on

this port. When admitAll(1),

untagged frames or Priority-

Tagged frames received on

this port will be accepted.
This attribute does not affect

VLAN-independent Bridge

Protocol Data Unit (BPDU)

frames, such as MVRP or

Spanning Tree Protocol (STP).

However, it does affect VLAN-

dependent BPDU frames, such

as MMRP.
If ingress filtering is enabled

on the same port, then

accepting untagged frames

only is not compatible, since

the combination effectively

leads to discarding all frames

on the port.

ieee8021QBridgePortAccepta

bleFrameTypes

(1.3.111.2.802.1.1.4.1.4.5.1.2)

All= Admit all

untagged and priority-

tagged frames.
Untagged= Admit

untagged frames only.
Tagged= Admit tagged

frames only.

All

Bridge Port Ingress

Filtering (filter)

The ingress filtering state of

the port.
When Enabled, the device

discards incoming frames for

VLANs that do not include the

port in its Member Set. When

Disabled, the device accepts

all incoming frames to the

port.
If untagged frames are

admitted on the port, then

ingress filtering is not

compatible, since the

combination effectively leads

to discarding all frames on the

port.

ieee8021QBridgePortIngressF

iltering

(1.3.111.2.802.1.1.2.1.4.5.3)

Enabled
Disabled

Disable

Содержание EtherHaul 1200











































































































































































































































Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды

Siklu EtherHaul 1200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды