Siklu EtherHaul 1200 Скачать руководство пользователя страница 216

Страница: 216 / 234

Installation and User Manual

EtherHaul

1200™

Page 216

EH-INST-02, Issue 4.0

Attribute (CLI

Attribute Name)

Description

SNMP Object ID

Value

Default

Connector

(connector)

An integer that indicates whether the

interface sublayer has a physical

connector.

ifConnectorPresent

(1.3.6.1.2.1.31.1.1.1.

17)

1 =True

(Connector is

present)
2=False True

(Connector is

absent)

N/A

Actual Ethernet

Type (eth-act-type)

This object identifier represents the

operational type of the MAU, as

determined by either:
The result of the auto-negotiation

process, or
If auto-negotiation is not enabled or is

not implemented for this MAU, then the

value that has been assigned in the

eth-type

attribute is used.

ifMauType

(1.3.6.1.2.1.26.2.1.1.

3)
Part of ifMauTable

(1.3.6.1.2.1.26.2.1)

For possible

values, refer to

Table

‎

11-20

1000fd

Table

‎

11-20 Ethernet Type Values

Value

Description

10hd

dot3MauType10BaseTHD (1.3.6.1.2.1.26.4.10)

10fd

dot3MauType10BaseTFD (1.3.6.1.2.1.26.4.11)

100hd

dot3MauType100BaseTXHD (1.3.6.1.2.1.26.4.15)

100fd

dot3MauType100BaseTXFD (1.3.6.1.2.1.26.4.16)

1000hd

dot3MauType1000BaseTHD (1.3.6.1.2.1.26.4.29)

1000fd

dot3MauType1000BaseTFD (1.3.6.1.2.1.26.4.30)

1000sxhd

dot3MauType1000BaseXHD (1.3.6.1.2.1.26.4.21)

1000sxfd

dot3MauType1000BaseXFD (1.3.6.1.2.1.26.4.22)

1000lxhd

dot3MauType1000BaseXHD (1.3.6.1.2.1.26.4.21)

1000lxfd

dot3MauType1000BaseXFD (1.3.6.1.2.1.26.4.22)

Содержание EtherHaul 1200











































































































































































































































Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды

Siklu EtherHaul 1200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды