Siklu EtherHaul 1200 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 234

background image

Installation and User Manual

EtherHaul

1200™

EH-INST-02, Issue 4.0

Page 117

Right_Master>set ring 3 action clear
Set done: ring 3
Right_Master>show log
Aug 4 21:43:18 sw cad: local Manual switch at 200 CW unblocked
ACW blocked
Aug 4 21:44:36 sw cad: ERP 200is ready Role acw-rpl

7.5.4

ERP Timers

Different timers are used to determine the time of fault reports and switching in order
to assure only necessary switching for permanent failures.

Timer

Description

Hold-off

Timer for ensuring stability of failure before triggering action to avoid

reporting a fault in case of intermittent failure.
0..10000 mSec (in 100mSec steps)

Guard

Timer for protecting device against old R-APS messages.
10..2000 mSec (in 10mSec steps)

Wait-to-Block

Timer for delaying switching triggered by administrative command (FS/MS).
5000..7000 mSec (in 100mSec steps)

Wait-to-Restore

Timer for delaying revertive operation.
1..12 minutes

7.5.5

ERP Configuration Example

The following example illustrates an ERP configuration:

Left_Master>show ring
ring 1 ring-id         : 1
ring 1 type          : ring
ring 1 fdb-id          : 1
ring 1 role         : none
ring 1 cw-port         : eth1
ring 1 acw-port        : eth0
ring 1 raps-md-level   : 7
ring 1 raps-svid       : none
ring 1 raps-cvid       : 100
ring 1 version     : v2
ring 1 revertive       : yes
ring 1 hold-off-timer  : 0
ring 1 guard-timer     : 500
ring 1 wtb-timer       : 5500
ring 1 wtr-timer       : 1

Right_Slave_72>show ring

ring 1 ring-id         : 1
ring 1 type         : ring
ring 1 fdb-id          : 1
ring 1 role         : acw-rpl
ring 1 cw-port         : eth0
ring 1 acw-port        : eth1
ring 1 raps-md-level   : 7
ring 1 raps-svid       : none
ring 1 raps-cvid       : 100
ring 1 version     : v2
ring 1 revertive    : yes
ring 1 hold-off-time   : 0
ring 1 guard-timer     : 500
ring 1 wtb-timer       : 5500
ring 1 wtr-timer       : 1

«
...
115
116
117
118
119
...
»

Содержание EtherHaul 1200











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EtherHaul 1200

Бренд: Naxa Страницы: 2

Бренд: AR Страницы: 24

Бренд: Diamond Antenna Страницы: 2

Бренд: A.H. Systems Страницы: 14

Tailgater VQ4500

Бренд: KING Страницы: 104

Бренд: TENNADYNE Страницы: 12

9707D-70 C-BAND TX

Бренд: Sea Tel Страницы: 83

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 10

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 12

Бренд: Philips Страницы: 12

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 11

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды