Siklu EtherHaul 1200 Скачать руководство пользователя страница 4

Страница: 4 / 234

Installation and User Manual

EtherHaul

1200™

Page 4

EH-INST-02, Issue 4.0

About this Document

This document is the Installation and User Manual for the EtherHaul 1200™ 70GHz
Wireless Link.

Audience

This document assumes a working knowledge of wireless backhaul platforms and their
operating environments.

This document is intended for use by all persons who are involved in planning, installing,
configuring, and using the EtherHaul system.

Conventions

The following conventions are used in this document in order to make locating, reading,
and using information easier.

Special Attention

Hint:

Informs you of a helpful optional activity that may be performed at the current
operating stage.

Note:

Provides important and useful information.

Caution:

Describes an activity or situation that may or will interrupt normal operation of the
EtherHaul system, one of its components, or the network.

Text Conventions

Document References

Italicized text is used to reference sections or chapters in this

document. In many cases, references use clickable hypertext links

that enable immediate access to referenced objects.

Command Input

Monospace text is used to help delineate command line user input

or text displayed in a command window.

Содержание EtherHaul 1200











































































































































































































































Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды

Siklu EtherHaul 1200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды