Siklu EtherHaul 1200 Скачать руководство пользователя страница 53

Страница: 53 / 234

Installation and User Manual

EtherHaul

1200™

EH-INST-02, Issue 4.0

Page 53

[rx-link-id <integer 0..127>]

[loopback {internal-mac-swap <modulation> <subchannels> <repetitions> <fec-rate>

- (from list of modulations) | disabled}]

[loopback-timeout <integer 0..86400>]

[tx-power <integer -35..5>]

4.5.3

Viewing Modulation Profiles Using the CLI

Use the

show modulation

command to display available supported modulation

profiles and their parameters.



CINR Low

– Lower threshold for stepping down in modulation profile

(Adaptive Mode).



CINR High

– Upper threshold for stepping up in modulation profile (Adaptive

Mode).



Backoff

– internal setting controlling the OFDM Tx power backoff.

Note that different modulation tables may apply according to the frequency channel
used.

Note:

Modulation parameters are optimized configuration and should not be altered by the
user

Содержание EtherHaul 1200











































































































































































































































Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды

Siklu EtherHaul 1200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды