Siklu EtherHaul 1200 Скачать руководство пользователя страница 227

Страница: 227 / 234

Installation and User Manual

EtherHaul

1200™

EH-INST-02, Issue 4.0

Page 227

Attribute (CLI

Attribute Name)

Description

SNMP Object ID

Value

Access

Default

Relay S-VID

(relay-svid)

The translated S-VID delivered

(received) over the EISS from a CNP or

PNP.
The VID must be defined in the VLAN

Table (Table

‎

11-28) and the Bridge

Port specified in the command must

belong to the S-component.
Because VID translation is

bidirectional, two entries cannot use

the same Relay S-VID for the same port.

Figure

‎

11-3 shows the bidirectional

relationships for Relay S-VID.

ieee8021PbVidTranslati

onRelayVid

(1.3.111.2.802.1.1.5.1.1.

1.2)

1..4094

N/A

Figure

‎

11-3 Bidirectional Definitions of S-VID Translation

11.12.13SNMP ifTable Attributes

Table

‎

11-32 SNMP ifTable Attributes

Attribute (CLI

Attribute Name)

Description

SNMP Object ID

SNMP

Access

Value

Description

A text string containing information

about the interface. This string

should include the name of the

manufacturer, the product name

and the version of the interface

hardware/software.

ifDescr

(1.3.6.1.2.1.2.2.1.2)

ASCII

representation of

the VLAN ID

Type

The type of interface. Additional

values for ifType are assigned by

the Internet Assigned Numbers

Authority (IANA), through updating

the syntax of the IANA ifType

textual convention.

ifType

(1.3.6.1.2.1.2.2.1.3)

l2vlan (135)

Содержание EtherHaul 1200











































































































































































































































Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды

Siklu EtherHaul 1200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EtherHaul 1200

Отзывы:

Похожие инструкции для EtherHaul 1200

Бренды по названию

Популярные бренды