Polaris RZR 570 2013 Скачать руководство пользователя страница 92

Страница: 92 / 482

3.20

9926813 R04 - 2013-2016

RZR

570 Service Manual

COOLANT DRAIN / RADIATOR REMOVAL

Coolant Drain

Remove the hood from the front cab.

WARNING

Never drain the coolant when the engine and radiator

are warm or hot. Hot coolant can cause severe burns.

Allow engine and radiator to cool.

Slowly remove the pressure cap to relieve any
cooling system pressure.

Place a suitable drain pan underneath the radiator
fitting on the front right-hand side of the vehicle.

Drain the coolant from the radiator by removing the
lower coolant hose

from the radiator as shown.

Properly dispose of the coolant.

Allow coolant to completely drain.

Place a suitable drain pan underneath the lower
engine hose

on the right-hand rear side of the

vehicle.

Remove the hose and completely drain the engine.

Radiator Removal

Remove the front bumper (see Chapter 10 – Front
Bumper, page 10.14).

Remove the upper engine outlet hose and recovery
hose from the top of the radiator.

10. Remove the two upper radiator retaining bolts and

the four bolts retaining the lower radiator mount
bracket. Remove the bracket from the frame.

11. Disconnect the fan motor and remove the radiator

from the vehicle. Take care not to damage the
cooling fins.

12. Reverse procedure for installation.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды