Polaris RZR 570 2013 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 482

background image

3.74

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

CRANKCASE BREATHER SERVICE

NOTE

The crankcase breather is serviceable with the engine

assembled and installed in the vehicle chassis.

1.

Remove the crankcase vent tube (if not already
performed).

2.

Remove the two fasteners securing the engine
breather cover to the engine.

3.

Remove the breather cover gasket and replace if
damaged.

4.

For reassembly, thoroughly clean the crankcase and
breather cover mating surfaces. Install a new gasket
and torque the two fasteners to specification.

TORQUE

Crankcase Breather Cover Bolts:

9 ft-lbs (12 Nm)

CRANKCASE SEPARATION

NOTE

Before the crankcase can be separated, be sure the

entire top end and oil pump assembly are removed

from the engine as outlined in this chapter.

1.

Rotate the engine on the engine stand so the
magneto side is facing upward.

2.

Remove the oil filter and the three fasteners

w

(20ft-

lbs (28Nm) apply loctite 272) that secure oil filter
adapter

q

to the crankcase. Discard O-rings and

through clean the adaptor for reassembly.

3.

Remove and discard the fifteen flange bolts from
magneto side crankcase evenly in a criss-cross
pattern.

ENGINE / COOLING SYSTEM

«
...
144
145
146
147
148
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: CadKat Страницы: 11

Transporta CCT 5221

Бренд: Ifor Williams Trailers Страницы: 45

Бренд: Suzuki Страницы: 624

Бренд: Massimo Страницы: 8

Utility Trailer

Бренд: OHIOSTEEL Страницы: 52

Бренд: Pongratz Страницы: 8

Бренд: Can-Am Страницы: 58

Бренд: Yamaha Страницы: 128

OneStopGardens 91240

Бренд: Harbor Freight Tools Страницы: 7

Бренд: Landoll Страницы: 78

1966 Snow Cruiser C-1560

Бренд: OMC Страницы: 20

Бренд: Razor Страницы: 12

Бренд: Yamaha Страницы: 354

Бренд: Yutrax Страницы: 7

Бренд: Taylor-Dunn Страницы: 130

GRIZZLY 450 YFM45FGY

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды