Polaris RZR 570 2013 Скачать руководство пользователя страница 241 | Manualshive

Страница: 241 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

5.35

10. Install the spider assembly onto the shaft with the

retaining ring on top of the spider.

NOTE

Align the skip tooth on the spider with the skip tooth on

the shaft.

11. Place the driven clutch into the Universal Clutch

Compressor.

Universal Clutch Compressor:

PU-50518

12. Press down on the top of the spider assembly,

pushing the spider onto the shaft.

13. Slowly compress the spider into place. If the spider

appears to bind while compressing, stop and make
sure the skip-tooth on the shaft and the spider are
aligned. Once the spider passes the retaining ring
notch on the shaft, install the retaining ring

s

.

14. Install the cam (helix) assembly over the shaft. Line

up the “X” on the cam, “X” on spider, and “X” on the
stationary sheave or use the marks previously made
before disassembly.

NOTE

If the cam assembly (helix) is difficult to install, be sure

the sheaves are aligned. To align the sheaves place the

clutch assembly on a flat surface with the cam

assembly (helix) side down. Press down on the

moveable sheave belt face with both hands and the

helix will release.

15. Use a T25 Torx driver to install the four helix retaining

screws

d

and torque to specification.

TORQUE

Helix Retaining Screws:

48 in-lb (5 Nm)

«
...
239
240
241
242
243
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

POLARIS SPORTSMAN 400

Бренд: Peg-Perego Страницы: 40

Бренд: Coleman Powersports Страницы: 46

Бренд: Land Pride Страницы: 50

outlander 400 series

Бренд: Can-Am Страницы: 156

Бренд: TGB Страницы: 269

Бренд: TGB Страницы: 306

Бренд: Erde Страницы: 4

Бренд: Ventrac Страницы: 83

Бренд: SSR Motorsports Страницы: 55

Бренд: Landoll Страницы: 88

Бренд: Landoll Страницы: 62

Бренд: YTL Страницы: 23

Бренд: Yamaha Страницы: 155

Бренд: Yamaha Страницы: 140

Бренд: Zap Страницы: 27

500 MXU IRS 4X4 NAKED EFI

Бренд: KYMCO Страницы: 1

Бренд: Power Fist Страницы: 8

Бренд: Suzuki Страницы: 477

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды