Polaris RZR 570 2013 Скачать руководство пользователя страница 446 | Manualshive

Страница: 446 / 482

background image

11.26

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

BATTERY ACTIVATION

WARNING

Battery electrolyte is poisonous. It contains sulfuric

acid. Serious burns can result from contact with skin,

eyes or clothing. Antidote:

External:

Flush with water.

Internal:

Drink large quantities of water or milk. Follow

with milk of magnesia, beaten egg, or vegetable oil. Call

physician immediately.

Eyes:

Flush with water for 15

minutes and get prompt medical attention.Batteries

produce explosive gases. Keep sparks, flame,

cigarettes etc. away. Ventilate when charging or using

in an enclosed space. Always shield eyes when

working near batteries. KEEP OUT OF REACH OF

CHILDREN.

WARNING

The gases given off by a battery are explosive. Any

spark or open flame near a battery can cause an

explosion which will spray battery acid on anyone close

to it. Should there be contact with battery acid, wash the

affected area with large quantities of cool water and

seek immediate medical attention.

To ensure maximum service life and performance from a
new battery, perform the following steps. NOTE: Do not
service the battery unless it will be put into regular
service within 30 days. After initial service, add only
distilled water to the battery. Never add electrolyte after a
battery has been in service.

NOTE

New Battery: Battery must be fully charged before use

or battery life will be significantly reduced 10-30% of the

battery’s full potential.

To activate a new battery:

1.

Remove all the filling plugs.

2.

Remove the sealing tube (red cap) from vent fitting.

3.

Place battery on a level surface. Fill battery with
electrolyte to upper level marks on the battery case.

NOTE

Never activate a battery on the vehicle. Electrolyte spills

can cause damage.

4.

Set battery aside to allow for acid absorption and
stabilization for 30 minutes.

5.

Add electrolyte to bring the level back to the upper
level mark on the battery case.

6.

Charge battery for 10 - 17 hours at 1 to 1.5 AMPS.

7.

Check during initial charging to see if electrolyte level
has fallen, and if so, fill with acid to the upper level.
After adding, charge for another hour at the same
rate.

NOTE

This is the last time that electrolyte should be added. If

the level becomes low after this point, add only distilled

water.

8.

When charging is complete, install the filling plugs
firmly.

NOTE

Do not apply excessive pressure. Finger tighten only.

Do not over-tighten.

9.

Wash off spilled acid with water and baking soda
solution, paying particular attention that any acid is
washed off the terminals. Dry the battery case.

BATTERY REMOVAL / INSTALLATION

See Chapter 2 “Maintenance” for battery removal and
installation procedures.

«
...
444
445
446
447
448
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Baltmotors Страницы: 58

Бренд: Coleman Страницы: 12

Бренд: E-TON Страницы: 118

Бренд: Honda Страницы: 232

Бренд: Hisun Страницы: 61

Бренд: AC Air Technology Страницы: 46

Бренд: Totem Страницы: 20

Бренд: NorAM Страницы: 613

Sportsman 9921837

Бренд: Polaris Страницы: 133

Бренд: Landoll Страницы: 64

Бренд: Panasonic Страницы: 392

Бренд: KAYO MOTOR Страницы: 138

Бренд: EBO Страницы: 19

Бренд: Yamaha Страницы: 156

2015 WILDCAT SPORT

Бренд: Arctic Cat Страницы: 68

Бренд: Arctic Cat Страницы: 84

Бренд: Arctic Cat Страницы: 177

Бренд: Arctic Cat Страницы: 190

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды