Polaris RZR 570 2013 Скачать руководство пользователя страница 95

Страница: 95 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.23

10. Remove the CPS sensor from the stator cover on the

right-hand side of the engine. Inspect CPS O-ring
and replace if needed.

11. Remove the oil dipstick.

12. Remove the eight bolts

retaining the water pump

cover to the stator cover.

13. Remove the water pump cover

and water pump

cover gasket

. Discard the water pump gasket.

14. Remove the water pump impeller

NOTE

The water pump impeller uses reverse (LH) threads.

15. Remove the thirteen bolts securing the stator cover

to the engine.

16. If needed, install the stator cover removal handle tool

(PA-49317) to the water pump cover bolt holes to aid
in stator cover removal.

CAUTION

The flywheel contains powerful magnets. Use caution

when removing the stator cover.

DO NOT place fingers between cover and crankcase at

any time during the removal process or injury could

result.

17. Remove and discard the stator cover gasket.

CAUTION

Be sure engine coolant does not contaminate the

engine oil during stator cover service.

18. Bring the stator cover assembly to a clean work

bench.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды