Polaris RZR 570 2013 Скачать руководство пользователя страница 369

Страница: 369 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

9.7

MASTER CYLINDER

REMOVAL

Locate the master cylinder above the left front tire in
the wheel well area.

Remove the clip (A) from the clevis pin (B) that
attaches the master cylinder to the brake pedal lever.

Place a container to catch brake fluid under the
master cylinder brake line banjo bolts (C).

CAUTION

Brake fluid will damage finished surfaces. Do not allow

brake fluid to come in contact with finished surfaces.

NOTE

Make note of front and rear brake line locations to

master cylinder.

Loosen the brake line banjo bolts (C) and allow fluid
to drain.

NOTE

Dispose of fluid properly. Do not re-use.

Remove the two mounting fasteners (D) that secure
the master cylinder to the frame.

INSTALLATION

Reverse Steps 1-5 for master cylinder installation.

Refer

the

torque

specifications

the

illustration.

After installing the foot brake check pedal freeplay.
Pedal freeplay should not exceed .090” (2.286 mm).

BRAKE SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды