Polaris RZR 570 2013 Скачать руководство пользователя страница 111

Страница: 111 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.39

ENGINE DISASSEMBLY / INSPECTION - TOP END

VALVE COVER REMOVAL

NOTE

The valve cover, camshafts, cylinder head, cylinder and

piston can be serviced with the engine installed in the

chassis.

If needed, remove the spark plug wire from the
engine.

Remove dirt and debris from valve cover area.

Remove the three valve cover shoulder bolts

and

isolators

using a T40 driver.

Carefully lift valve cover from the engine and remove
it out of the right-hand rear wheel well area.

Replace isolators

and valve cover seal

if oil

leaks are evident.

Remove the spark plug

. Stuff spark plug hole with

a shop towel to prevent anything from falling into the
combustion chamber (if further engine disassembly
is required).

CAMSHAFT / CARRIER REMOVAL

NOTE

The camshafts can be removed with the engine

installed in the chassis.

Rotate the engine so the piston is at Top Dead
Center (TDC) on the compression stroke.

NOTE

To verify TDC, see the

“SETTING TDC”, page

section in this chapter.

Remove the hydraulic cam chain tensioner

from

the cylinder. Replace the sealing washer

upon

reassembly.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды