Polaris RZR 570 2013 Скачать руководство пользователя страница 108

Страница: 108 / 482

3.36

9926813 R04 - 2013-2016

RZR

570 Service Manual

15. Install the throttle body and air box. Tighten the hose

clamps that secure the throttle body to the intake
duct, intake boot and air box.

16. Install the lower stater motor bolt through the lower

starter motor mounting boss.

17. Instal the starter motor onto the engine.

18. Install the starter motor and battery cables as

outlined in Chapter 10.

TORQUE

Starter Motor Fastener:

7 ft-lb (10 Nm)

19. Connect the harness leads to the IAC valve (D), TPS

(E), T-MAP sensor (F). Verify routing is correct.

20. Connect the fuel injector harness lead (G) to the fuel

injector.

21. Connect the fuel line (H) to the fuel rail.

22. Install the eight fasteners securing the two bolt in

braces to the vehicle main frame. Torque fasteners
to

specification.

sure

the

routing

the

transmission breather hose and wire harness is
correct.

TORQUE

Rear Bolt in Brace Fastener:

17 ft-lb (23 Nm)

Front Bolt in Brace Fastener:

40 ft-lbs (54 Nm)

23. Connect the ignition coil harness connector and

install the spark plug wire.

24. Install the CPS and mounting bolt into the stator

cover and torque to specification.

TORQUE

CPS Fastener:

9 ft-lb (12 Nm)

25. Connect the stator wire connector and install a new

tie strap to secure the wiring to the front engine
mount bracket.

26. Install the inner clutch cover as outlined in the PVT

chapter.

27. Install the drive clutch, driven clutch, belt and outer

clutch cover as outlined in the PVT chapter. Be sure
all hose and wire routings are correct. Torque all
fasteners to specification.

28. Install the intake baffle assembly. Secure the 3

clamps that attach the assembly to the crankcase
vent, air box lid and inner clutch cover.

29. Install the rear bumper and cargo box assembly as

outlined in the body chapter.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды