Polaris RZR 570 2013 Скачать руководство пользователя страница 145

Страница: 145 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.73

10. Inspect surfaces of pump cavity in crankcase and

surface of pump cover for scoring or wear.

11. Inspect gerotor for scoring or other damage. Replace

parts as a set if damaged.

OIL PUMP ASSEMBLY

Clean and dry all parts thoroughly. Apply clean
engine oil to all parts. Do not use gasket sealer on
the pump cover mating surfaces.

Align the gerotor according to the orientation dots.

Place the drive pin

through the oil pump drive

shaft.

Slide the gerotor

onto the drive shaft and lock

them into position on the drive pin.

Install the washer

onto the drive shaft.

Install the oil pump cover

onto the shaft assembly.

Grasp the complete oil pump assembly by the drive
shaft and install the assembly into the crankcase.

Install the three oil pump cover bolts and torque to
specification.

TORQUE

Oil Pump Cover Bolt:

8 ft-lbs (11 Nm)

Torque cover bolts to specification.

TORQUE

Oil Pump Cover Bolts:

8 ft-lbs (11 Nm)

FLUID CAPACITY

Oil Capacity

Approx. 2 Quarts (1.9 L)

Oil Filter Wrench

PU-50105 or 2.5” (64 mm)

Oil Type

Polaris PS-4 Synthetic Engine Oil

Oil Pressure

Minimum Specification

(using Polaris PS-4 at operating temperature)

10 PSI @ 1200 RPM (Minimum)
40 PSI @ 7000 RPM (Minimum)

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды