Polaris RZR 570 2013 Скачать руководство пользователя страница 165

Страница: 165 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

4.5

SERVICE NOTES

• For more convenient and accurate testing of EFI components, it is recommended dealers utilize the Digital Wrench®

Diagnostic Software (dealer only), or testing may be done manually using the procedures provided.

•

80% of all EFI problems are caused by wiring harness connections.

• For the purpose of troubleshooting difficult running issues, a known-good ECU from another

RZR

570 of the same

model and year may be used without damaging system or engine components.

• Never attempt to service any fuel system component while engine is running or ignition switch is "on."

• Cleanliness is essential and must be maintained at all times when servicing or working on the EFI system. Dirt, even

in small quantities, can cause significant problems.

• Do not use compressed air if the system is open. Cover any parts removed and wrap any open joints with plastic if

they will remain open for any length of time. New parts should be removed from their protective packaging just prior
to installation.

• Clean any connector before opening to prevent dirt from entering the system.

• Although every precaution has been taken to prevent water intrusion failure, avoid direct water or spray contact with

system components.

• Do not disconnect or reconnect the wiring harness connector to the control unit or any individual components with

the ignition "on." This can send a damaging voltage spike through the ECU.

• Do not allow the battery cables to touch opposing terminals. When connecting battery cables attach the positive

(red) cable to positive (+) battery terminal first, followed by negative (black) cable to negative (-) battery terminal.

• Never start the engine when the cables are loose or poorly connected to the battery terminals.

• Never disconnect battery while engine is running.

• Never use a battery boost-pack to start the engine.

• Do not charge battery with key switch "on."

• Always disconnect negative (-) battery cable lead before charging battery.

• Always unplug ECU from the wire harness before performing any welding on the unit.

FUEL SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды