Polaris RZR 570 2013 Скачать руководство пользователя страница 414

Страница: 414 / 482

10.14

9926813 R04 - 2013-2016

RZR

570 Service Manual

BODY COMPONENT REMOVAL

SEATS

To remove any of the seats, lift upward on the latch
lever located behind the seat bottom.

Lift upward and forward on the seat while lifting up
on the latch lever and remove the seat from the
vehicle.

REAR SERVICE PANEL

Remove driver and passenger seats.

Turn both latches 1/4 turn to disengage the panel.

Lift the panel upward and towards the front of the
vehicle to remove it.

FRONT BUMPER

Remove the four push rivets from the sides of the
front bumper.

Remove the six Torx screws retaining the upper,
middle and lower portion of the bumper.

Disconnect the front head lamp connectors and
remove the front bumper from the vehicle.

BODY / FRAME

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды