Polaris RZR 570 2013 Скачать руководство пользователя страница 94

Страница: 94 / 482

3.22

9926813 R04 - 2013-2016

RZR

570 Service Manual

13. Follow this procedure in reverse to assemble the

water pump impeller and cover. Always use a

new

water pump cover gasket. Torque all fasteners in
sequence to specification.

TORQUE

Water Pump Cover Fastener:

9 ft-lb (12 Nm)(Apply Loctite® 204™ to bolt threads)

14. Fill and bleed cooling system as outlined in this

chapter.

WATER PUMP MECHANICAL SEAL / OIL
SEAL REPLACEMENT

NOTE

The stator cover must be removed from the engine to

service the water pump drive shaft, oil seal, mechanical

seal and bearing.

Allow engine and cooling system to completely cool.

CAUTION

Be sure the engine has cooled and no pressure is built
up in the cooling system before removing the pressure

cap. The coolant may be hot and could cause severe

injury or burns.

Remove both seats and the engine service panel.

Disconnect the (-) negative battery cable.

Remove all debris and thoroughly clean water pump
area and right-hand side of engine block.

Remove the hood.

Remove the pressure cap from the filler neck.

Completely drain cooling system and engine as
outlined in this chapter.

Raise and safely support the vehicle. Remove the
right-hand rear wheel.

Disconnect the stator wire connector and cut the tie
strap securing the wiring to the front engine mount
bracket.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды