Polaris RZR 570 2013 Скачать руководство пользователя страница 438 | Manualshive

Страница: 438 / 482

background image

11.18

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

SPEED SENSOR TESTING

Special Tools Required:
Static Timing Light Harness (PN 2871745)
Hall Sensor Probe Harness (PN 2460761)

1.

Disconnect the 3 wire harness from the speed
sensor

and

remove

the

sensor

from

the

transmission.

2.

Connect the wires from the Static Timing Light
Harness to the sensor 3 pin connector using the Hall
Sensor Probe Harness (PN 2460761).

3.

Pass a screwdriver back and forth in front of the
sensor tip.

4.

Be sure connections are good and 9V battery is in
good condition. If the light flashes, the sensor is
good.

DIFFERENTIAL SOLENOID OVERVIEW

The differential solenoid is located on the rear portion of
the transmission case. The solenoid actuates a shift fork
with an engagement dog, which locks and unlocks the
rear differential. Refer to Chapter 8 for more information.

DIFFERENTIAL SOLENOID CIRCUIT
OPERATION

The Rear Diff Solenoid Relay is attached to the lower
airbox bracket and can be accessed through the right
rear wheel well.

When the switch is pushed to activate “TURF”, a ground
signal is provided to the ECU from the AWD / 2WD /
TURF Switch.
Depending on engine speed and gear position criteria,
the ECU energizes the Rear Diff Solenoid Relay allowing
it to enable the differential solenoid.
If the rear diff fails to switch from operational modes:

• Check the solenoid and relay connectors. Look for

loose wires or bad connections.

• Check for power from the relay connector, to ensure

the solenoid has power to be activated.

• Check the AWD / 2WD / TURF Switch wires for loose

connections.

• Remove solenoid from rear differential and ensure the

solenoid plunger is actuating.

CAUTION

Do not power the solenoid with 12 Volts for more than 1

second, or damage may occur to solenoid.

«
...
436
437
438
439
440
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

DRIFTER 10-0550

Бренд: Kolpin Страницы: 17

Can-Am Maverick Sport X mr 1000R

Бренд: BRP Страницы: 192

Бренд: Skeeter Страницы: 18

Бренд: Panasonic Страницы: 29

Бренд: Can-Am Страницы: 58

MINITRANSPORTER MECH 35

Бренд: Fort Страницы: 64

600 INDY Voyager 2014

Бренд: Polaris Страницы: 132

600 INDY SP 2019

Бренд: Polaris Страницы: 178

KODIAK 700 2018

Бренд: Yamaha Страницы: 180

Бренд: Yamaha Страницы: 150

Grizzly YFM35FGIX

Бренд: Yamaha Страницы: 164

KODIAK YFM700FWBD 2017

Бренд: Yamaha Страницы: 176

KODIAK 700 YFM70KDXG

Бренд: Yamaha Страницы: 180

Бренд: Yamaha Страницы: 126

Бренд: REDCAT Страницы: 21

Бренд: Taylor-Dunn Страницы: 109

2003 Cadillac DeVille

Бренд: GM International Страницы: 423

Бренд: CRG Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды