Polaris RZR 570 2013 Скачать руководство пользователя страница 229

Страница: 229 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

5.23

19. Remove sheave from puller.

20. Remove installation tool.

Cover Bushing Removal

21. Install main adapter (8) on puller.

22. Install adapter reducer (9).

23. From outside of clutch cover, insert removal tool (3)

into cover bushing.

24. With inside of cover toward vise, slide cover onto

puller. With inside of cover toward vise, slide cover
onto puller.

25. Install nut onto puller rod and hand tighten. Turn

puller barrel to increase tension as needed.

26. Turn clutch cover counterclockwise on puller rod until

bushing is removed and cover comes free.

27. Remove nut from puller rod and set aside.

28. Remove bushing and bushing removal tool from

puller. Discard bushing.

Cover Bushing Installation

29. Apply Loctite® 648 evenly to bushing bore in cover.

30. Working from inside of cover, insert new bushing and

bushing installation tool into center of clutch cover.

31. With main adapter on puller, insert cover onto puller

rod, placing outside of cover toward vise.

32. Install nut on rod and hand tighten. Turn puller barrel

to apply more tension if needed.

33. Turn clutch cover counterclockwise on puller rod until

bushing is seated.

34. Remove nut from puller rod. Take installation tool and

clutch cover off rod.

DRIVE CLUTCH ASSEMBLY

CAUTION

Do not apply oil or grease to the bushings.

Reassemble the drive clutch in the following sequence.
Be sure the marks that were made during disassembly
are aligned during each phase of assembly.

1. Install the shift weights, bolts and nuts onto the

movable

sheave. Torque shift weight bolts to

specification.

TORQUE

Shift Weight Bolt:

20 in-lb (2 Nm)

2. Install the non-braking needle bearing

, the two

washers

and the spacer

onto the stationary

sheave

3. Install movable sheave onto stationary sheave shaft.

Be sure the movable sheave slides freely on the
spacer.

4. Apply 0.4 mL of Loctite® 620™ and 0.4 mL of

Loctite® 7088™ Primer in 90º apart in vertical stripes
to the shaft threads.

PVT SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды