Polaris RZR 570 2013 Скачать руководство пользователя страница 243 | Manualshive

Страница: 243 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

5.37

TROUBLESHOOTING

TROUBLESHOOTING

SITUATION

PROBABLE CAUSE

REMEDY

Engine RPM
below specified
operating range,
although engine
is properly tuned.

Wrong or broken drive clutch spring.

Replace with recommended spring.

Drive clutch shift weight too heavy.

Install correct shift weight kit to match engine
application.

Driven clutch spring broken or installed in
wrong helix location.

Replace spring; refer to proper installation
location.

Erratic engine
operating RPM
during
acceleration or
load variations.

Drive clutch binding.

A. Disassemble drive clutch; inspect shift
weights for wear and free operation.
B. Clean and polish stationary shaft hub;
reassemble clutch without spring to determine
problem area.

Belt worn unevenly - thin / burnt spots.

Replace belt.

Driven clutch malfunction.

A. Replace ramp buttons.
B. Inspect movable sheave for excessive
bushing clearance.

Sheave face grooved.

Replace the clutch.

Engine RPM
above specified
operating range.

Incorrect drive clutch spring (too high spring
rate).

Install correct recommended spring.

Drive clutch shift weights incorrect for
application (too light).

Install correct recommended shift weights.

Drive clutch binding.

Disassemble and clean clutch, inspecting shift
weights and rollers. Reassemble without the
spring and move sheaves through entire range
to further determine probable cause.

Driven clutch binding.

Disassemble, clean, and inspect driven clutch,
noting worn sheave bushing and ramp buttons
and helix spring location.

Converter sheaves greasy; belt slipage.

Clean sheaves with denatured alcohol or brake
cleaner, install new belt.

Harsh drive clutch
engagement.

Drive belt worn too narrow.

Replace belt.

Excessive belt / sheave clearance with new
belt.

Perform belt / sheave clearance adjustment with
shim washers beneath spider.

Drive belt turns
over

Wrong belt for application.

Replace with correct belt.

Belt burnt, thin
spots

Abuse (continued throttle application when
vehicle is stationary, excess load).

Caution operator to operate machine within
guidelines.

Dragging brake.

Inspect brake system.

Slow, easy clutch engagement.

Fast, effective use of throttle for efficient
engagement.

PVT cover
overheating
(melting)

Plugged air intake or outlet.

Clear obstruction.

«
...
241
242
243
244
245
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Sinclair Страницы: 36

Lynx 1200 4-TEC 900 ACE 2018

Бренд: BRP Страницы: 164

Бренд: Ezgo Страницы: 102

Бренд: HAKO Страницы: 190

Бренд: CAMSO Страницы: 50

Бренд: Suzuki Страницы: 215

Бренд: FamilyFun Страницы: 13

Бренд: Can-Am Страницы: 127

Бренд: Ultra-tow Страницы: 9

2012 700 i Cruiser

Бренд: Arctic Cat Страницы: 708

Sportsman 850 2021

Бренд: Polaris Страницы: 180

Бренд: Humbaur Страницы: 200

Бренд: Tao Motor Страницы: 73

Бренд: NC Страницы: 79

Raider mini 90S

Бренд: Dazon Страницы: 60

Бренд: CHICAGO Страницы: 25

Бренд: PACIFIC RIM INT’L WEST Страницы: 21

Бренд: Suzuki Страницы: 508

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды