Polaris RZR 570 2013 Скачать руководство пользователя страница 261

Страница: 261 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

6.17

21. Remove the retaining ring, washer, needle bearing,

and sprocket from the reverse shaft (see Figure 8-1).

22. Tilt the two shafts towards each other and remove

the silent chain from the two shafts.

23. If necessary, disassemble the other end of the

reverse shaft. Remove the bearing, engagement
dog, retaining ring, washer, gear and needle bearing
from the reverse shaft (see Figure 8-2).

24. To disassemble the shift shaft rail remove the snap

ring (X) from the end of the shift rail on either side.

CAUTION

Use caution when disassembling the shift rail. The

compressed springs on the shift rail may pop off

causing eye or face injury.

Snorkel Shaft Removal / Disassembly

CAUTION

The pinion shaft must be removed prior to removing the

snorkel shaft assembly. Failure to remove pinion shaft,

will result in damage to the snorkel shaft.

25. Extract the seal from the snorkel shaft to access the

snorkel tube for removal.

26. Using the Snorkel Tool (PA-50231), fully loosen the

snorkel tube.

TRANSMISSION

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды