Polaris RZR 570 2013 Скачать руководство пользователя страница 425 | Manualshive

Страница: 425 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

11.5

The rider information display is located in the instrument cluster. All segments will light up for 1 second at start-up.

NOTE

If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the instrument cluster may

have shut off to protect the electronic speedometer.

q

Vehicle Speed Display

- Analog display of vehicle speed in MPH or km/h.

w

Information Display Area - Odometer / Trip Meter / Tachometer / Engine Temperature / Engine Hours /

Service Info / Clock

- LCD display of the service hour interval, total vehicle miles or km., total engine hours, a trip

meter, engine RPM and engine temperature.

e

MPH / KM/H Display

- MPH is displayed when the instrument cluster is in the

Standard

mode. KM/H is displayed

when the instrument cluster is in the

Metric

mode.

r

High Beam Indicator

LED icon illuminates whenever the Headlamp switch is in the high beam position.

t

Fuel Level Indicator

- LCD bar graph indicating current fuel level. All segments will flash when the last segment

is cleared indicating a low fuel warning.

y

Clock

- Displays current time in either 12-hour or 24-hour formats.

u

Engine Temperature Indicator

- LED icon illuminates when the ECM determines the engine is overheating. The

indicators will initially flash to indicate the engine is overheating. The indicators will stay lit and not flash if a severe
overheating condition exists.

i

Service Interval Indicator

- Preset at the factory and adjustable by the user, a flashing wrench symbol alerts the

operator that the preset service interval has been reached and maintenance should be performed. The wrench icon
will flash for 10 seconds upon start-up once it reaches 0.

o

Check Engine MIL

- Illuminated when the ECM has detected a Diagnostic Trouble Code in the engine

management system.

a

AWD Indicator

- Illuminated when the AWD / TURF switch is in the

AWD

position.

s

TURF Indicator

- Illuminated when the AWD / TURF switch is in the

TURF

position (INTL Models Only).

d

Neutral Gear Indicator

- LED icon illuminates when gear selector is in the neutral (N) position.

f

Gear Position Indicator -

Displays gear selector position.

• H = High
• L = Low
• N = Neutral
• R = Reverse
• P = Park
• – = Gear Signal Error (shifter stuck between gears)

g

Power Steering System MIL -

LED icon illuminates when a fault has occurred with the power steering system.

This indicator illuminates when the key is turned to the ON position and goes off when the engine is started.

h

Turn Signal / Hazard Lamp Indicator

- LED icon illuminates whenever the LH, RH or hazard lamps are activated

(INTL Models Only).

j

Helmet / Seat Belt Indicator

- LED icon illuminates for several seconds when the key is turned to the ON

position. The lamp is a reminder to the operator to ensure all riders are wearing helmets and seat belts before
operating the vehicle.

«
...
423
424
425
426
427
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: FARMA Страницы: 36

120 Sno Pro 2010

Бренд: Arctic Cat Страницы: 562

Бренд: Polaris Страницы: 690

Бренд: Makita Страницы: 128

Бренд: ASV Страницы: 60

Falcon Go-kart 2018

Бренд: J&J Amusements Страницы: 58

Бренд: Iron Baltic Страницы: 44

Бренд: TOMCAR Страницы: 22

Бренд: Arctic Cat Страницы: 70

Бренд: Arctic Cat Страницы: 101

Бренд: Dometic Страницы: 96

Бренд: Stels Страницы: 139

Бренд: Xingyun Страницы: 92

Бренд: Landa Страницы: 30

Бренд: Arctic Cat Страницы: 64

2012 90 Utility

Бренд: Arctic Cat Страницы: 83

Бренд: Yamaha Страницы: 374

Бренд: MANCO Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды