Polaris RZR 570 2013 Скачать руководство пользователя страница 349 | Manualshive

Страница: 349 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

8.13

FRONT SUSPENSION

REMOVAL / REPLACEMENT

The following procedure details upper and lower A-arm
removal and replacement on one side of the vehicle.

1.

Elevate and safely support the front of the vehicle
and remove the front wheel.

2.

Remove lower shock fastener (A) from the upper A-
arm.

3.

Remove upper ball joint pinch bolt (B) from bearing
carrier.

4.

Using a soft face hammer, tap on bearing carrier to
loosen the upper A-arm ball joint end while lifting
upward on the upper A-arm. Completely remove the
ball joint end from the bearing carrier.

5.

Remove the front bumper to allow A-arm bolt
removal.

6.

Loosen and remove the upper A-arm through-bolt
fastener (C) and remove the upper A-arm from the
vehicle.

7.

Examine A-arm bushings and pivot tube (see
“Exploded

View”).

Replace

if

worn.

Discard

hardware.

WARNING

The locking agent on the existing bolts was destroyed

during removal. DO NOT reuse old hardware. Serious

injury or death could result if fasteners come loose

during operation.

8.

If not replacing the A-arm, thoroughly clean the A-
arm and pivot tube.

9.

Install new ball joint into A-arm. Refer to “Ball Joint
Replacement” section.

10. Insert new A-arm bushings and pivot tube into new

A-arm.

11. Install new upper A-arm assembly onto vehicle

frame. Torque new bolt to specification.

TORQUE

Front Upper / Lower A-arm Bolts:

39 ft-lb (53 Nm)

12. Insert upper A-arm ball joint end into the bearing

carrier. Install upper ball joint pinch bolt (B) into the
bearing carrier and torque bolt to specification.

TORQUE

Front Ball Joint Pinch Bolts:

23 ft-lb (31 Nm)

13. Attach shock to A-arm with spacer (D) or washer (G)

and fastener (A). Torque lower shock bolt to
specification.

14. Remove lower ball joint pinch bolt (E) from bearing

carrier.

15. Using a soft face hammer, tap on bearing carrier to

loosen the lower A-arm ball joint end while pushing
downward on the lower A-arm. Completely remove
the ball joint end from the bearing carrier.

16. Loosen and remove the lower A-arm through-bolt

fastener (F) and remove the lower A-arm from the
vehicle.

17. Examine A-arm bushings and pivot tube (see

“Exploded

View”).

Replace

if

worn.

Discard

hardware.

18. If not replacing the A-arm, thoroughly clean the A-

arm and pivot tube.

19. Install new ball joint into A-arm. Refer to “Ball Joint

Replacement” section.

20. Insert new A-arm bushings and pivot tube into new

A-arm.

21. Install new lower A-arm assembly onto vehicle

frame. Torque new bolt to specification.

TORQUE

Front Upper / Lower A-arm Bolts:

39 ft-lb (53 Nm)

STEERING / SUSPENSION

«
...
347
348
349
350
351
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: E-Z-GO Страницы: 158

Trail Boss 330 Quadricycle

Бренд: Polaris Страницы: 119

Бренд: Hisun Страницы: 116

Бренд: Ardisam Страницы: 10

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 136

Бренд: Yamaha Страницы: 132

YFB250K Timberwolf

Бренд: Yamaha Страницы: 159

Бренд: Yamaha Страницы: 214

Sportsman 800 EFI

Бренд: Polaris Страницы: 388

Power Wheels B9273

Бренд: Fisher-Price Страницы: 44

2015 39 Roadster NEV

Бренд: ACG Страницы: 77

2013 RANGER 500 EFI CREW Midsize

Бренд: Polaris Страницы: 14

Бренд: Landoll Страницы: 70

Renegade 570 2016

Бренд: Can-Am Страницы: 534

Бренд: Yamaha Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды