Polaris RZR 570 2013 Скачать руководство пользователя страница 403 | Manualshive

Страница: 403 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

10.3

CAB FRAME

ASSEMBLY / REMOVAL

NOTE

Finger tighten all components until cab frame is

completely assembled on vehicle, then tighten to

specifications listed.

1.

Assemble the rear cab frame and the front cab frame
at the coupler joints and secure with four (3/8-16 x 1
1/4) screws and (3/8-16 Nyloc) nuts. Tighten screws
to specification.

2.

Place the assembled cab frame onto the vehicle and
align the rear mount holes. Fasten the rear cab
frame brackets to vehicle with four (5/16-18) bolts
and (5/16-18) nuts. Tighten bolts to 16-18 ft-lbs (22-
24 Nm). Fasten the two self-tapping screws to the
rear inner portion of the bracket on each side.
Tighten screws to specification.

3.

Place the straps from the safety net over the front
coupler posts.

4.

Fasten the front of the cab frame to the base
brackets and secure with four (3/8-16 x 1 1/4) screws
and

(3/8-16

Nyloc)

nuts.

Tighten

screws

to

specification.

5.

Attach side bars to cab frame using M6 screws and
nuts on top and M8 screws and nuts on the bottom.
Tighten to specification.

TORQUE

3/8-16 x 1 1/4 Screws:

25-28 ft-lbs (34 Nm)

5/16-18 Screws:

15 ft-lbs (20 Nm)

3/8-16 x 1 1/4 Nyloc Nuts:

28 ft-lb (38 Nm)

M6 Screws (Hip Bolster Bolts):

8 ft-lb (11 Nm)

6.

To remove the cab frame, reverse the assembly
procedure (steps 1-5).

«
...
401
402
403
404
405
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

1997 Fourtrax TRX250

Бренд: Honda Страницы: 155

Wagon with tilt

Бренд: Texas Страницы: 42

Vyper 4WD 1100cc 4 seater XY1100UEL

Бренд: gio Страницы: 261

Бренд: Buffalo Tools Страницы: 2

Haul-Master 64831

Бренд: Harbor Freight Tools Страницы: 16

Бренд: Polaris Страницы: 476

Viper 40E (RXL-40E)

Бренд: E-TON Страницы: 24

SmarTrax John Deere 8770

Бренд: Raven Страницы: 48

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 859

Sasquatch 1000W

Бренд: Daymak Страницы: 24

Бренд: Yamaha Страницы: 112

Magnum 500 2000

Бренд: Polaris Страницы: 5

Бренд: Polaris Страницы: 13

600 IQ Widetrak

Бренд: Polaris Страницы: 140

2008 Scrambler 500 2X4 International

Бренд: Polaris Страницы: 124

Supersport 2007

Бренд: Polaris Страницы: 266

Бренд: Metal-Fach Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды