Polaris RZR 570 2013 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 482

background image

2.26

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

SHIFT CABLE INSPECTION / ADJUSTMENT

Shift cable adjustment may be necessary if symptoms
include:

• No AWD or gear position display on instrument cluster
• Ratcheting noise on deceleration
• Inability to engage into a gear
• Excessive gear clash (noise)
• Gear selector moving out of desired range

1.

Locate the shift cable

q

in the rear right wheel well

area.

2.

Inspect shift cable, clevis pin

w

, pivot bushings, and

dust boot

e

. Replace if worn or damaged.

3.

If adjustment is required: Loosen outer jam nut

r

and inner jam nut

t

so there is slack in the cable

and neither jam nut touches the shift cable mount.

4.

Adjust the shift cable so there is the same amount of
cable travel when shifting slightly past the detents of
HIGH (H) gear and PARK (P).

5.

Thread jam nut as required to obtain proper cable
adjustment.

NOTE

This procedure may require a few attempts to obtain

the proper adjustment.

6.

Once the proper adjustment is obtained, place the
shift cable and inner jam nut into the mount. Tighten
the outer jam nut against the mount.

7.

Start engine and shift through all gears to ensure the
shift cable is properly adjusted. If transmission still
ratchets after cable adjustment, the transmission will
require service.

FRONT GEARCASE LUBRICATION

NOTE

It is important to follow the front gearcase maintenance

intervals described in the Periodic Maintenance Chart.
Regular fluid level inspections should be performed as

well.

The front gearcase fluid level should be checked and
changed in accordance with the maintenance schedule.

• Be sure vehicle is positioned on a level surface when

checking or changing the fluid.

• Check vent hose to be sure it is routed properly and

unobstructed.

Front Gearcase Fluid Level Check

The fill plug is located on the bottom right side of the front
gearcase. Access the fill plug through the right front
wheel well. Maintain fluid level even with the bottom of
the fill plug hole.

1.

Position vehicle on a level surface.

2.

Remove the fill plug

q

and check the fluid level.

3.

If fluid level is not even with the bottom threads, add
the recommended fluid as needed. Do not overfill.

«
...
60
61
62
63
64
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Taylor-Dunn Страницы: 126

Бренд: Massimo Motor Страницы: 165

Бренд: Ezgo Страницы: 64

Бренд: BOMBARDIER Страницы: 20

Бренд: Oldenbourg group Страницы: 60

Бренд: Clam Corp Страницы: 4

Бренд: Clam Corp Страницы: 6

Бренд: Lyda Страницы: 55

Бренд: PRONAR Страницы: 166

Бренд: Miller Electric Страницы: 20

Бренд: YBIKE Страницы: 12

Бренд: SANMEN COUNTY YONGFU MACHINE Страницы: 73

FourTrax Foreman TRX520FE2 2020

Бренд: Honda Страницы: 287

Бренд: Yamaha Страницы: 44

Бренд: Hammerhead Страницы: 70

Бренд: Hammerhead Off-Road Страницы: 75

Бренд: SAFARI Страницы: 50

Бренд: GAS GAS Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды