Polaris RZR 570 2013 Скачать руководство пользователя страница 355 | Manualshive

Страница: 355 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

8.19

STABILIZER BAR REMOVAL

1.

If stabilizer bar linkages are installed, remove the nut
and linkage bushings (see “Exploded View”).

2.

Remove the hood and front bumper (see Chapter 10
– BODY COMPONENT REMOVAL, page

).

3.

Remove the four T30 Torx fasteners retaining the
front bumper support to the frame.

NOTE

Properly support the bumper support and wires that are

attached.

4.

Remove the two upper radiator retaining bolts (A)
and remove the four bolts (B) retaining the lower
radiator mount bracket and remove the bracket from
the frame

5.

Allow radiator to sag down to allow access to
recovery bottle retaining screws and filler neck
retaining screws.

6.

Remove retaining screws from recovery bottle and
filler neck. Allow the recovery bottle and filler neck to
hang down to access the four bolts retaining the
upper radiator mount bracket.

7.

Remove the four bolts retaining the upper radiator
mount bracket and remove the bracket from the
frame.

8.

Lift up on the stabilizer bar and remove it from the
vehicle.

STEERING / SUSPENSION

«
...
353
354
355
356
357
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Komatsu Страницы: 4

Бренд: Kinroad Страницы: 80

ST SHUTTLE 4/6 E 2008

Бренд: E-Z-GO Страницы: 66

Бренд: Yerf-Dog Страницы: 40

eTiger ATV50S BLUE

Бренд: LAMAX Страницы: 150

Бренд: KAYO MOTO Страницы: 14

MARSH MASTER 2015

Бренд: COAST MACHINERY Страницы: 59

Бренд: Yamaha Страницы: 150

Бренд: Toro Страницы: 12

1990 DS Gasoline Golf Car

Бренд: Club Car Страницы: 20

Бренд: Club Car Страницы: 44

Бренд: Bad Boy Страницы: 60

Бренд: URBANGLIDE Страницы: 16

Club Car CARRYALL 710 LSV ELECTRIC

Бренд: Ingersoll-Rand Страницы: 108

Бренд: X-PRO Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды