Polaris RZR 570 2013 Скачать руководство пользователя страница 149

Страница: 149 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.77

Place the crankshaft in a truing stand or V-blocks
and measure the runout where indicated below with
a dial indicator.

Maximum Runout:

Mag side (3) - 0.00118″ (0.03 mm)

PTO side (4) - 0.00590″ (0.15 mm)

PTO SIDE CRANKCASE BEARING SERVICE

Bearing Removal

NOTE

Due to extremely close tolerances and minimal wear,

the bearings must be inspected visually, and by feel.

Look for signs of discoloration, scoring or galling. Turn

the inner race of each bearing. The bearings should

turn smoothly and quietly. The outer race of each

bearing should fit tightly in the crankcase. The inner

race should be firm with minimal side to side movement

and no detectable up and down movement.

Bearings are stressed during the removal process and

must not be re-used!

Remove and discard the PTO side crankshaft seal.
Replace with new for assembly.

If not already performed, remove the screws that
secure the bearing retainer to the case.

Remove the retaining ring.

Support the crankcase and drive, press, or extract
the three bearings with a blind bearing remover.

REF

DESCRIPTION

Bearing Retainer Bolt

8 ft-lbs (11 Nm)

apply loctite 272

Bearing Retainer

Bearings

Apply Loctite® 641 to the inner race of
each of the crank bearings.

Bearing Spacer

Retaining Ring

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды