Polaris RZR 570 2013 Скачать руководство пользователя страница 341

Страница: 341 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

8.5

Apply Loctite

271 (Red) to the outer circumference

of the new upper bearing race. Slide the new upper
bearing onto the steering shaft and press it into the
pivot tube by hand.

NOTE

Use care not to allow any of the Loctite

to get in the

bearing.

Bearings will be seated in the pivot housing upon

tightening the steering wheel nut in step 14.

Reinstall the upper washers and spacers in the order
in which they were removed.

10. Install the steering wheel and hand tighten the nut.

11. Reinstall the steering shaft assembly in the vehicle.

Install the lower portion of the steering shaft onto the
steering gear box assembly (see Figure 5-16).
Torque the lower pinch bolt to specification.

TORQUE

Lower Pinch Bolt:

36 ft-lb (48 Nm)

12. Install the two fasteners that retain the pivot tube

(see Figure 5-17). Torque fasteners to specification.

TORQUE

Pivot Tube Fasteners:

23 ft-lb (31 Nm)

13. Install the fastener retaining the upper portion of the

steering wheel tilt shock to the pivot tube (see Figure
5-17). Torque fastener to specification.

TORQUE

Tilt Shock Fastener:

7 ft-lbs (10 Nm)

14. Be sure the front wheels are facing straight forward.

Remove the steering wheel and align as needed.
Torque the steering wheel nut to specification.

TORQUE

Steering Wheel Nut:

65 ft-lbs (88 Nm)

15. Wipe the pivot tube clean of any excess Loctite.

16. Install steering wheel cap and field test steering

operation.

STEERING / SUSPENSION

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды