Polaris RZR 570 2013 Скачать руководство пользователя страница 244

Страница: 244 / 482

5.38

9926813 R04 - 2013-2016

RZR

570 Service Manual

SITUATION

PROBABLE CAUSE

REMEDY

Belt slippage due to water, oil, grease, etc.,
rubbing on cover.

Inspect system. Clean , repair or replace as
necessary.
Seal PVT system ducts.

Clutches or weight being applied to cover
while in operation.

Remove weight. Inform operator

High vs. low range.

Instruct operator on guidelines for operation in
proper driving range for different terrain as
outlined in Owner’s Safety and Maintenance
Manual.

Water ingestion

Cover seals or ducts leaking.

Find leak and repair as necessary.

Operator error.

Instruct operator on guidelines for operation in
wet terrain as outlined in Owner’s Safety and
Maintenance Manual.

Belt slippage

Belt worn out.

Replace belt.

Water ingestion.

Inspect and seal PVT system.

Belt contaminated with oil or grease.

Inspect and clean.

PVT noise

Belt worn or separated, thin spots, loose
belt.

Replace belt.

Broken or worn clutch components, cover
hitting clutches.

Inspect and repair as necessary.

Engagement
erratic or stabby

Thin spots on belt, worn belt .

Replace belt. Refer to belt burnt troubleshooting
and instruct operator.

Drive clutch bushings stick.

Inspect and repair clutches.

PVT SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды