Polaris RZR 570 2013 Скачать руководство пользователя страница 232 | Manualshive

Страница: 232 / 482

background image

5.26

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

CLUTCH DISASSEMBLY / INSPECTION

NOTE

Driven clutch compression springs ARE NOT

INTERCHANGABLE between

early build

2013 vehicles

and

late build

2013 vehicles. Early 2013 driven clutch

assemblies use a shorter compression spring (3.85”)

and washer. Late 2013 driven clutch assemblies use a

longer compression spring (3.95”) and no washer.

CAUTION

BASE and INTL Models ONLY:

Hold outer sheave

securely to relieve spring pressure while removing

the retaining bolt.

1.

Mark the position of the clutch sheaves before clutch
removal or use the X’s

q

on the sheaves for

reference. This aids in reassembly and maintains
clutch balance after reassembly.

2.

Remove the driven clutch from the vehicle. (See PVT
Disassembly, page 5.8).

3.

Place the driven clutch into a universal clutch
compressor. Spin the tool down until it touches the
spring cup or retaining plate

w

.

Universal Clutch Compressor:

PU-50518-A

4.

Using a T30 Torx driver, remove the five screws

e

that secure the spring retainer to the inner clutch
sheave.

5.

Turn the compression tool handle counter-clockwise
to relieve spring pressure and allow the spring cup
and retaining ring to move out from the moveable
sheave.

6.

Remove the compressor tool from the clutch
assembly.

7.

Remove the spring retainer

r

, spring cup

t

, spring

y

and washer (early build only) from the inner clutch

sheave.

8.

Separate the stationary and the moveable sheaves.
Keep track of the number of thrust washers between
the sheaves.

«
...
230
231
232
233
234
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Kinroad Страницы: 80

Бренд: KTM Страницы: 190

Бренд: 3M Страницы: 20

Бренд: E-Z-GO Страницы: 66

Бренд: Landoll Страницы: 64

Бренд: Kubota Страницы: 112

Бренд: Kayo Страницы: 4

Бренд: Kayoba Страницы: 16

Бренд: Chapman Страницы: 27

Бренд: Yamaha Страницы: 148

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 142

Бренд: Schmeiser Страницы: 28

Бренд: Sodi Страницы: 50

12004TC Twister 1600

Бренд: Toro Страницы: 44

Бренд: MULTIQUIP Страницы: 10

Бренд: MULTIQUIP Страницы: 54

Бренд: KidNme Motorsports Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды