Polaris RZR 570 2013 Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

7.21

5.

Make sure the circlip

w

is on the shaft and not left in

the joint.

6.

Remove the boot from the shaft.

CAUTION

Complete disassembly of the plunging joint is NOT

recommended. The internal components are precision

fit and develop their own characteristic wear patterns.

Intermixing the internal components could result in

looseness, binding, and/or premature failure of the joint.

IMPORTANT

If the grease in the joint is obviously contaminated with

water and/or dirt, the joint should be replaced.

7.

Thoroughly clean the joint with an appropriate
solvent and dry the joint to prevent any residual
solvent from being left in the joint upon reassembly.

8.

Visually inspect the joint for damage. Replace if
needed.

9.

Clean the splines on the end of the shaft and apply a
light coat of grease prior to reassembly.

10. Slide the small boot clamp and boot (small end first)

onto the drive shaft and position the boot in its
groove machined in the shaft.

11. Install a

new

circlip on the end of the shaft.

12. Grease the joint with the special joint grease

provided in the boot replacement kit. Fill the cavity
behind the balls and the splined hole in the joint’s
inner race. Pack the ball tracks and outer face flush
with grease. Place any remaining grease into the
boot.

CAUTION

The grease provided in the replacement kit is specially
formulated for wear resistance and durability. DO NOT

use substitutes or mix with other lubricants.

NOTE

The amount of grease provided in the boot kit is pre-

measured. Use entire contents of package.

13. Fully compress the joint and push the drive shaft

firmly into the inner race.

14. Align the circlip with the lead-in chamfer.

15. Use a soft-faced hammer to tap the joint onto the

drive shaft until you reach the end of the splines and
the joint locks in place.

16. Pull on the joint to test that the circlip is seated and

that the joint is securely fastened to the shaft.

17. Remove excess grease from the plunging joint’s

external surfaces and place the excess grease in the
boot.

18. Pull the boot over the joint and position the boot lips

into the grooves on the joint housing and shaft. Make
sure the boot is not dimpled or collapsed.

«
...
317
318
319
320
321
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

JACOBSEN 4800 2006+

Бренд: E-Z-GO Страницы: 114

700 Diesel ATV 2007

Бренд: Arctic Cat Страницы: 184

Бренд: Honda Страницы: 83

Бренд: Clam Corp Страницы: 4

Бренд: Clam Corp Страницы: 6

Sportsman 400 Lift

Бренд: Polaris Страницы: 7

2009 Outlander 500 EFI

Бренд: Can-Am Страницы: 152

Бренд: DAELIM Страницы: 26

Бренд: PRONAR Страницы: 132

Бренд: JI-EE Страницы: 61

Бренд: KAYO MOTOR Страницы: 138

Бренд: Taylor-Dunn Страницы: 232

Бренд: Yamaha Страницы: 431

ET 1-50 48 Volts

Бренд: Taylor-Dunn Страницы: 153

Бренд: KAYO MOTO Страницы: 9

Бренд: SCORPION Страницы: 32

Бренд: Reeves Страницы: 8

Cargo Compact Series

Бренд: Peecon Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды