Polaris RZR 570 2013 Скачать руководство пользователя страница 433

Страница: 433 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

11.13

AWD / 2WD SWITCH

Disconnect the AWD / 2WD switch harness by
depressing the connector locks and pulling on the
connector. Do not pull on the wiring.

Test between the 2 sets of outputs (AWD / 2WD). If
any of the tests fail, replace the switch assembly.

• Move the switch to AWD (ON). There should be con-

tinuity between switch pins 2 and 3.

• Move the switch to 2WD (NONE / OFF). There should

be no continuity between any pins.

AWD / 2WD / TURF SWITCH - LE / INTL

Disconnect the AWD / 2WD / TURF switch harness
by depressing the connector locks and pulling on the
connector. Do not pull on the wiring.

Test between the 3 sets of outputs (AWD / 2WD /
TURF). If any of the tests fail, replace the switch
assembly.

• Move the switch to AWD. There should be continuity

between switch pins 2 and 3; 5 and 6.

• Move the switch to 2WD. There should be no continuity

between any pins.

• Move the switch to TURF. There should be continuity

between switch pins 1 and 2; 4 and 5.

ELECTRICAL

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды