Polaris RZR 570 2013 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

3.41

CAMSHAFT INSPECTION

Inspect all main journals and cam lobes as described
below and compare to specifications. Replace camshafts
or cylinder head if worn beyond service limit or if any
surface is pitted or damaged.

1.

Visually inspect each cam lobe for wear or damage.

2.

Measure the height of each cam lobe from the base
circle to highest point on the lobe using a
micrometer. Compare to specification.

NOTE

Replace camshafts if damaged or if any part is worn

past the service limit.

MEASUREMENT

Camshaft Lobe Height:

Intake: 1.5704" ± 0.0038" (39.89 ± 0.097 mm)

Exhaust: 1.5405" ± 0.0038" (39.13 ± 0.097 mm)

EXHAUST CAMSHAFT DECOMPRESSION
MECHANISM

NOTE

Removal of the decompression mechanism is not

necessary unless replacement is required.

1.

Thoroughly clean and inspect the decompression
mechanism

q

located on the exhaust camshaft.

2.

Replace

the

decompression

assembly

if

any

excessive wear or binding is evident.

3.

Be sure the decompression mechanism functions
smoothly and easily returns under spring pressure to
the resting position against gravity.

CAM CHAIN AND GUIDE SERVICE

NOTE

The crankcase has a removable lower cam chain drive

guide that prevents the chain from disengaging the

crankshaft during engine service.

The cam chain, cam chain guides and cam chain

tensioner can be replaced with the engine installed in

the vehicle.

1.

If not already performed, remove the valve cover,
stator cover, flywheel, cam chain tensioner, cam
carrier and camshafts as outlined in this chapter.

2.

Remove the two fasteners

q

that secure the cam

chain guides

w

to the crankcase.

3.

Remove the fastener

e

that secure the lower cam

chain guide

r

to the crankcase.

4.

Inspect the cam chain guides and replace if
excessive wear is evident.

ENGINE / COOLING SYSTEM

«
...
111
112
113
114
115
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Yamaha Страницы: 26

Бренд: Kellfri Страницы: 16

2005 TRX400EX Sportrax 400EX

Бренд: Honda Страницы: 238

Camoplast ATV T4S

Бренд: CAMSO Страницы: 10

Бренд: KTM Страницы: 197

Бренд: MADER Страницы: 115

MARGAY racing K3

Бренд: Ignite Страницы: 30

Бренд: Kellfri Страницы: 12

Бренд: Yamaha Страницы: 94

Бренд: Centaur Страницы: 56

Бренд: Metal-Fach Страницы: 60

Бренд: Husqvarna Страницы: 56

Бренд: Husqvarna Страницы: 60

Бренд: Husqvarna Страницы: 60

Бренд: Husqvarna Страницы: 74

Workman 133-0959

Бренд: Toro Страницы: 8

Workman MDE 07299

Бренд: Toro Страницы: 44

Бренд: Toro Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды