Polaris RZR 570 2013 Скачать руководство пользователя страница 114

Страница: 114 / 482

3.42

9926813 R04 - 2013-2016

RZR

570 Service Manual

Upon installation, torque all fasteners to specification
and reassemble engine and vehicle as outlined in
this chapter.

TORQUE

Cam Chain Guide Fasteners:

9 ft-lb (12 Nm)

CYLINDER HEAD REMOVAL

NOTE

The cylinder head can be serviced with the engine

installed in the chassis.

Do not rotate head assembly up side-down until the

valve tappets have been removed.

Remove and discard the two outer M6 bolts

that

retain the cylinder head

and the cylinder.

Loosen the four cylinder head bolts

evenly 1/8

turn (60 degrees) at a time until all are loose.

Remove and discard the cylinder head bolts

Replace with

new

upon assembly.

Tap cylinder head lightly with a soft faced hammer
until loose. Tap only in reinforced areas or on thick
parts of the cylinder head casting.

Remove the cylinder head

and head gasket

CYLINDER HEAD DISASSEMBLY

CAUTION

Wear eye protection during cylinder head disassembly

and reassembly or when working with the valve springs.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды