Polaris RZR 570 2013 Скачать руководство пользователя страница 379

Страница: 379 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

9.17

FRONT BRAKE PADS

PAD REMOVAL

Elevate and support front of vehicle.

CAUTION

Use care when supporting vehicle so that it does not tip

or fall. Severe injury may occur if machine tips or falls.

Remove the front wheel.

Loosen the pad adjuster screw 2-3 turns.

Remove and discard the upper and lower caliper
mounting bolts and remove the caliper from the front
hub.

NOTE

When removing caliper, use care not to damage brake

line. Support caliper so to avoid kinking or bending

brake line.

Push caliper piston into caliper bore slowly using a
C-clamp or locking pliers with pads installed.

NOTE

Brake fluid will be forced through compensating port

into master cylinder fluid reservoir when piston is

pushed back into caliper. Remove excess fluid from

reservoir as required.

Push the mounting bracket inward and the slip outer
brake pad out between the bracket and caliper body.

Remove the inner pad from the bracket and caliper.

BRAKE SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды