Polaris RZR 570 2013 Скачать руководство пользователя страница 115

Страница: 115 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.43

NOTE

Keep mated parts together and in order with respect to

their location in the cylinder head for assembly

purposes. It is important to install cylinder head

components back in the same location. Mark each

component or place them in an organized rack as you

remove them.

Remove the valve tappet

from the cylinder head.

Compress the valve spring by hand using valve
spring compressor adapter.

Valve Spring Compressor Adapter

PV-43513-A

Push down on the spring and remove the split
keepers

Slowly release valve spring pressure and remove the
compressor adapter.

Remove the valve retainer

, valve spring

, valve

stem seal

and valve spring seat

. Discard the

valve seal.

NOTE

Replace valve seals whenever cylinder head is

disassembled. Hardened, cracked or worn seals will

cause excessive oil consumption.

Lift up the cylinder head and push the valve

out,

keeping it in order for reassembly in the same valve
guide.

Repeat the previous steps to remove the remaining
valves.

Clean the combustion chamber and head gasket
surface.

CYLINDER HEAD INSPECTION

Thoroughly clean cylinder head surface to remove all
traces of gasket material and carbon.

CAUTION

Use care not to damage gasket sealing surface. All

gasket surfaces must be clean, dry and free of any oil

or grease upon assembly. Clean sealing surfaces with

rubbing alcohol or electrical contact cleaner. Do not

touch sealing surfaces of the new head gasket.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды