Panasonic VF200 Скачать руководство пользователя страница 170

Страница: 170 / 289

Appendix Function Parameter List

・

The retry interval is set with parameter “P026: Waiting Time”.

・

Fault alarm is not output during retry operation. But when the fault still

occurs even if retry is performed for preset times, the fault alarm will be

output.

・

If an unselected fault occurs during retry, the fault alarm will be output and

the retry count accumulated till present will be cleared.

・

Once the power is cut off, the retry count accumulated till now will be

cleared.

・

If the fault does not occur for over 5 minutes, the retry times accumulated up

to now will be cleared.

・

When speed search is selected with parameter “P165: Speed Search Select

during Retry” and the time set with parameter “P026: Waiting Time” and “P163:

Waiting Time to Speed Search” has elapsed, the speed search function will

start to operate.

■

Related parameter: P026

P024

Start Mode

This parameter is used to set the start-up operation for the case that a run

signal set externally is input when the power is turned ON.

Depending on the start mode setting, when the run

signal is ON, the inverter may start (restart) suddenly if

the power is turned ON or restored after a power failure.

Therefore, do not approach the unit. Design the machine

so that personal safety can be ensured even if the inverter

starts suddenly.

Depending on the start mode function setting, if the fault

trip is reset with the run signal ON, the inverter may

sometimes restart suddenly. (Please take measures to

ensure personal safety.)

Failure to do so may lead to injury.

Содержание VF200


































































































































































































































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Panasonic VF200, Инструкция по эксплуатации

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды