Panasonic VF200 Скачать руководство пользователя страница 218

Страница: 218 / 289

Appendix Function Parameter List

211

P088

PWM Signal Average Times

The inverter measures and calculates ON time and OFF time of each PWM

cycle used as frequency command.

When using this parameter, the times of each PWM cycle command should

be averaged, and then the average operation times are set as final output

frequency.

Data setting range

(times)

1 to 100

* If average times are increased, the frequency command will become stable,

but the response speed will decrease.

Related parameters: P087, P089

P089

PWM Signal Cycle

PWM signal cycle can be input with this parameter.

Data can be set within

12.5% of the input PWM signal cycle.

Data setting range

(ms)

1 to 2000

The output frequency controlled by PWM signal is “0 V stop or the minimum

frequency (without ON status)” and “the maximum frequency (without OFF

status)”.

・

Due to the fact that the output frequency accuracy relative to input signal will

decrease around the minimum frequency and maximum frequency, do not

use the inverter for precise frequency control.

・

The 2

frequency setting signal is prior to PWM frequency signal when the

frequency setting signal is selected (ON).

・

PID control function is invalid when PWM frequency signal is selected.

PWM frequency signal cannot be used as PID setting value (SP).

Related parameters: P087, P088

Содержание VF200


































































































































































































































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Panasonic VF200, Инструкция по эксплуатации

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды