Panasonic VF200 Скачать руководство пользователя страница 138

Страница: 138 / 289

11. Specifications

Note 1) Rated output current of 3.7 kW+ inverters varies with the set carrier

frequency. Derate the output current as shown in the following figure.

•

3.7 kW to 11 kW Type

•

15 kW Type

Note 2) Rated output capacity: refers to the value at output voltage of 230 VAC

for 1-phase 200 V type and the value at output voltage of 460 VAC for

3-phase 400 V type.

Note 3) The power supply capacity varies with source impedance. Please use

a power supply as shown on the above table.

Note 4) If excessive amount of current flows through the circuit repeatedly or

the unit is used under high temperature, overcurrent trip may occur.

•

For 200 V/0.75 kW inverter, if the carrier frequency is above 7.5 kHz,

overcurrent trip will occur to cause reduction of overcurrent protection

capability.

•

For 200 V/1.5 kW inverter, if the carrier frequency is above 5 kHz, overcurrent

trip will occur to cause reduction of overcurrent protection capability.

Содержание VF200


































































































































































































































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Panasonic VF200, Инструкция по эксплуатации

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды