Panasonic VF200 Скачать руководство пользователя страница 123

Страница: 123 / 289

9. Troubleshooting

116

Indication

Details and causes of abnormality

Remedies

OU2

•

Internal DC overvoltage at constant

speed

Remove sharp variations at load side
(parameters P002, P062, P064 and
P066).

OU1

•

Internal DC overvoltage during

deceleration

•

Extend deceleration time.

•

Power supply voltage below 85% of its

rating

•

Measure power supply voltage and

check input for open phase.

•

Check ride-through restart function.

•

The output current exceeds 125% of

electronic thermal setting current or
140% of rated current of inverter for more
than 1 minute.

•

Check electronic thermal setting

current.

•

Check and adjust torque boost level

(parameter P007).

•

Reduce load.

•

Heat sink overheating

•

Check ambient temperature.

•

External fault stop input signal is input

from control circuit terminals.

•

Check if the external signal is proper

and if timing circuit is correct.

•

The power is turned ON with run signal

ON.

•

Timeout detected

•

The communication cable comes off.

•

The operation panel comes off.

•

Check start mode (parameter P057).

•

Check communication setting and

wiring.

•

Reduce the interference around the

inverter.

•

Check the connection between

operation panel and the inverter.

FAN

•

Cooling fan abnormality

•

Check if the cooling fan is locked.

SEr

•

Speed search failed

•

Incorrect motor rotation direction

•

The rating of the motor is too small

compared with that of inverter.

•

Motor rotates slowly during normal

operation.

•

Reduce the noise around the

inverter.

•

Check the rotation direction of motor.

CPU

•

Too much interference is applied to the

inverter

•

Reduce the interference around the

inverter.

Er1*

•

Communication between the inverter

unit and the operation panel failed

•

Check if the operation panel is

connected properly to the unit.

Er2

•

VF200 unit firmware version>Operation

panel firmware version

•

Check the firmware version.

The details of abnormality corresponding to “Er1” are not displayed in monitor

functions n020 to n023.

Содержание VF200


































































































































































































































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Panasonic VF200, Инструкция по эксплуатации

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды