Panasonic VF200 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 289

background image

4. Operation Method (Basic Operation)

44

4.1 Safety Precautions

・

Always close the terminal cover before turning ON the

inlet power.

・

Do not open the terminal cover while the power is ON.

Failure to do so may result in an electric shock or fire.

・

Do not operate the switches or dials with wet hands.

Failure to do so may result in an electric shock.

・

Do not touch the inverter terminals when the inverter

power is ON or even when the inverter is stopped.
Failure to do so may result in an electric shock.

・

The STOP button is not designed for emergency stop

purpose, so set a separate button for emergency

stop.

Failure to do so may result in injury.

・

The heat sinks and braking resistors are at high

temperature, so do not touch them.
Failure to do so could lead to burn.

・

The inverter can easily be switched to high speed from

low speed, so confirm the allowable range of the motor
and machine before making settings.
Failure to do so could lead to injury.

・

Set separate holding brakes if required.

Failure to do so could lead to injury.

・

Before turning on the power, check the following points again.

1. Check if all wirings are correct or not again.
  Reversed wirings between power supply and load in
  particular could damage the inverter.
2. Check if the voltage rating of the inverter matches
  with power supply.
3. Check if a phase-lead capacitor is connected to the motor.
  Connection of phase-lead capacitor could result in
  faults to the inverter and capacitor.
4. Confirm the set frequency before starting a trial operation.

«
...
49
50
51
52
53
...
»

Содержание VF200


































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VF200

Atlona OmniStream AT-OMNI-111

Бренд: Panduit Страницы: 105

Atlona Omega AT-OME-RX21

Бренд: Panduit Страницы: 28

Бренд: U.S. Converters Страницы: 19

Бренд: CHD Elektroservis Страницы: 20

AT-IMC100T/SCMM

Бренд: Allied Telesis Страницы: 20

Бренд: B&B Electronics Страницы: 3

Бренд: Badger Meter Страницы: 12

Бренд: B&B Electronics Страницы: 2

Бренд: T+A Страницы: 64

Бренд: Ensemble Designs Страницы: 27

Бренд: APT Страницы: 43

Бренд: Orgautomatech Страницы: 8

Бренд: DigiTech Страницы: 4

Бренд: GoMax Electronics Страницы: 16

AVerCaster Combo

Бренд: Avermedia Страницы: 2

Бренд: Xerox Страницы: 2

Бренд: Fuba Страницы: 35

Бренд: Vital Systems Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды